784936
14
Zoom out
Zoom in
Previous page
1/24
Next page
11
CONTROL PANEL OPERATION
3. Press the Light button to store the F1 cycle
and move to the F2 cycle.
4. Press the Plus or Minus button to adjust
the cycle time for F2.
5. Wait 15 seconds to allow the exit timer to
expire and store the setting.
IMPORTANT: To reset the first filter cycle start
time, skip step 5 and continue pressing the Mode
button until the actual temperature is displayed.
Powering down of the spa will also reset the first
filter start time.
FILTER CYCLE SUSPENSION:
The
filter cycle will be suspended every time a jet pump
or light is activated manually during the filter cycle
time. The suspension will end 10 minutes after the
completion of the manual use.
OPERATIONAL MODES
The Standard Mode is the default operational
mode preset from the factory. In order to program
the spa to operate in other modes you must enter
the programming mode to make the change.
NOTE: Freeze Protection (Smart Winter Mode) will
assert as necessary during all modes.
STANDARD MODE:
Is programmed to
maintain the desired temperature with periodic
water circulation (sampling) to sample and heat
the water to the set temperature.
ECONOMY MODE:
This will reduce the set
temperature of the spa by 11°C. Water sampling
and heating of the water is only done during the
filter cycles.
SLEEP MODE:
Water sampling and
heating is only done during the filter cycles
while trying to bring the spa water up to the
set temperature.
QUIET MODE:
Maintains temperature with
periodic sampling between the start of F1 and the
end of F2 while not allowing any water sampling
to happen between the end of F2 and the start
of F1.
To enter the programming screen and toggle
between Standard, Economy, Sleep and Quiet
Modes the following is required:
1. Press and hold the Light button for 5 sec-
onds.
2. Press the Light button several times until
ST, Ec, SL, or NT is displayed.
3. Use the Plus or Minus button to choose
between the Modes.
ST = Standard Mode, Ec = Economy
Mode, SL Sleep = Mode and NT = Quiet
Mode.
4. Wait 15 seconds to allow the exit timer to
expire and store the setting.
OFF MODE:
This mode allows you to stop all
spa functions for 30 minutes to perform quick spa
maintenance. To place the spa in OFF MODE,
press and hold the Jets button for 5 seconds.
The display will toggle between OFF and water
temperature when in the OFF MODE. To stop the
OFF MODE before the 30 minute cycle time is
complete, simply tap (short press) the Jet button.
FAHRENHEIT/CELSIUS SETTING
T
o change water temperature display to either
Fahrenheit or Celsius, press and hold Light button
for 5 seconds until F1... is displayed. Press the
Light button several times until F or C is displayed.
Press the Plus or Minus button to change. Wait 15
seconds to allow the exit timer to expire and store
the setting.
SMART WINTER MODE
The Smart Winter Mode (SWM) is used to prevent
water from freezing in the plumbing of the spa. As
soon as there is a risk of freezing, this protection
automatically kicks in. The SWM protection will
turn back off only after 24 hours without a risk of
freezing. During this 24 hour period, the Smart
Winter Mode icon remains on; the icon blinks
when the purge is active.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fantasy Embrace 2019 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fantasy Embrace 2019 in the language / languages: English as an attachment in your email.

The manual is 0.56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info