Manual Falmec Mira Top - wall (page 20 of 80) (All languages)

709844

Zoom out

Zoom in

1/80

INSTALLATION

only intended for qualied personnel

Before installing the hood,

carefully read the chapter

'SAFETY INSTRUCTIONS AND WARNINGS'.

TECHNICAL FEATURES

The technical specications are exhibited on the labels located inside

the hood.

POSITIONING

The minimum distance between the highest part of the cooking

equipment and the lowest part of the hood is indicated in the in-

stallation instructions.

Generally, when the hood is placed over gas cookers, the distance must

be at least 65 cm (25.6''). However, according to an interpretation of

standard EN60335-2-31 dated 11-07-2002 of TC61 (sub-clause 7.12.1

meeting 15 agenda item 10.11), the minimum distance between the

cooker and lower part of the hood can be reduced to the quota report-

ed in the installation instructions.

Should the instructions for the gas cooker specify a greater distance,

this must be taken into consideration.

Do not install the hood outdoors and do not expose it to outdoor envi-

ronment (rain, wind, etc.).

ELECTRICAL CONNECTION

(only intended for qualied personnel)

Disconnect the equipment from electrical mains power

supply before carrying out any operations on the hood.

Ensure that the wires inside the hood are not disconnected

or cut:

in the event of damage, contact your nearest Servicing Depart-

ment.

Refer to qualied personnel for electrical connections.

Connection must be carried out in compliance with the provisions

of law in force.

Before connecting the hood to the electrical mains power supply,

check that:

• voltage supply corresponds with what is reported on the data plate

located inside the hood;

• the electrical system is compliant and can withstand the load (see

the technical specications located inside the hood);

• the power supply plug and cable do not come into contact with

temperatures exceeding 70 °C;

• the power supply system is eectively and properly connected to

earth in compliance with regulations in force;

•

the socket used to connect the hood is within reach.

In case of:

• devices tted with cables without a plug: the type of plug to use is

a ''standardised'' one. The wires must be connected as follows: yel-

low-green for earthing, blue for neutral and brown for the phase. The

plug must be connected to an adequate safety socket.

•

xed equipment not provided with a power supply cable and plug,

or any other device that ensures disconnection from the electrical

mains, with an opening gap of the contacts that enables total discon-

nection in overvoltage category III conditions.

Said disconnection devices must be provided in the mains power

supply in compliance with installation regulations.

The yellow/green earth cable must not be cut o by the switch.

The Manufacturer declines all responsibility for failure to comply with

the safety regulations.

FUMES DISCHARGE

EXTERNAL EXHAUST HOOD SUCTION

In this version the fumes and vapours are discharged

outside through the exhaust pipe.

To this end, the hood outlet tting must be connected

via a pipe, to an external output.

The outlet pipe must have:

• a diameter not less than that of the hood tting.

• a slight slope downwards (drop) in the horizontal sections to prevent

condensation from owing back into the motor.

• the minimum required number of bends.

• the minimum required length to avoid vibrations and reduce the

suction performance of the hood.

You are required to insulate the pipes if it passes through cold envi-

ronments.

In the presence of motors with 800m

/h or higher, a check valve is

present to prevent external air owing back.

Deviation for Germany:

when the kitchen hood is used at the same time as appliances that are pow-

ered by energy other than electricity, the negative pressure in the room must

not exceed 4 Pa (4 x 10-5 bar).

HOOD WITH INTERNAL RECIRCULATION FILTERING

In this model, the air passes through the charcoal lters

to be puried and recycled in the environment.

Ensure that the active carbon lters are assembled into

the hood, if not, install them as indicated in the assem-

bly instructions.

In this version the check valve must not be assembled: remove

it if it is on the air outlet tting of the motor.

ASSEMBLY INSTRUCTIONS

only intended for qualied personnel

The hood can be installed in various congurations.

The generic assembly steps apply to all installations; for

each case, follow the specic steps provided for the re-

quired installation.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Falmec Mira Top - wall in the language / languages: All languages as an attachment in your email.

The manual is 19,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Falmec Mira Top - wall Manual

Product: