Manual Falmec Gruppo Incasso Pro (page 13 of 60) (All languages)

709807

Zoom out

Zoom in

1/60

ENGLISH

MAINTENANCE

Before cleaning or carrying out maintenance operations, disconnect the

equipment by removing the plug or switching o the main switch.

Do not use detergents containing abrasive, acidic or corrosive substances

or abrasive cloths.

Regular maintenance guarantees proper operation and performance over time.

Special attention is to be paid to the metal anti-grease lters: frequent cleaning of the

lters and their supports ensures that no ammable grease is accumulated.

CLEANING OF EXTERNAL SURFACES

You are advised to clean the external surfaces of the hood at least once every 15 days

prevent oily substances and grease from sticking to them. To clean the brushed stainless

steel hood, the Manufacturer recommends using "Magic Steel" wipes.

Alternatively and for all the other types of surfaces, it can be cleaned using a damp cloth,

slightly moistened with mild, liquid detergent or denatured alcohol.

Finish o cleaning by rinsing well and drying with soft cloths.

Do not use too much water next to the push button control panel and

lighting devices in order to prevent humidity from reaching electronic

parts.

The glass panels can only be cleaned with specic, non-corrosive or non-abrasive deter-

gents using a soft cloth.

The Manufacturer declines all responsibility for failure to comply with these instructions.

CLEANING OF INTERNAL SURFACES

Do not clean electrical parts, or parts related to the motor inside the hood,

with liquids or solvents.

For the internal metal parts, see the previous paragraph.

METAL ANTI-GREASE FILTERS

It is advised to frequently wash the metal lters (at least once a month) leaving them to

soak in boiling water and cleaning solution for 1 hour, taking care not to bend them.

Do not use corrosive, acid or alkaline detergents.

Rinse them well and wait for them to be completely dry before reassembling them.

They are dishwasher safe.

To extract and insert the metal anti-grease lters see the assembly instructions.

LIGHTING

The range hood is equipped with high eciency, low consumption LED spotlights with

extremely long duration under normal use conditions.

Should the LED spotlight need to be replaced, proceed as shown in the gure.

12V

GREASE DRIP TRAY

It is advisable to clean the tray every 15 days.

Do not use corrosive, acid or alkaline detergents.

For more thorough cleaning, remove the oil collection tray (see gure) and wash it with

hot water and washing up liquid. Rinse it well and wait for it to be completely dry before

reassembling it. They are dishwasher safe.

DISPOSAL AFTER END OF USEFUL LIFE

The crossed-out trash or refuse bin symbol on the appliance means that the

product is WEEE, i.e. “Waste electrical and electronic equipment'', accordingly it

must not be disposed of with regular unsorted waste (i.e. with ''mixed house-

hold waste''), but it must be disposed of separately so that it can undergo specif-

ic processing for its re-use, or a specic treatment, to remove and safely dispose of any

substances that may be harmful to the environment and remove the raw materials that can

be recycled. Proper disposal of these products contributes to saving valuable resources and

avoid potential negative eects on personal health and the environment, which may be

caused by inappropriate disposal of waste.

You are kindly asked to contact your local authorities for further information regarding the

designated waste collection points nearest to you. Penalties for improper disposal of such

waste can be applied in compliance with national regulations.

INFORMATION ON DISPOSAL IN EUROPEAN UNION COUNTRIES

The EU WEEE Directive was implemented dierently in each country, accordingly, if you wish

to dispose of this appliance we suggest contacting your local authorities or dealer to nd

out what the correct method of disposal is.

INFORMATION ON DISPOSAL IN NONEUROPEAN UNION COUNTRIES

The crossed-out trash or refuse bin symbol is only valid in the European Union: if you wish

to dispose of this appliance in other countries, we suggest contacting your local authorities

or dealer to nd out what the correct method of disposal is.

WARNING!

The Manufacturer reserves the right to make changes to the equipment at any time and

without prior notice. Printing, translation and reproduction, even partial, of this manual are

bound by the Manufacturer's authorisation.

Technical information, graphic representations and specications in this manual are for in-

formation purposes and cannot be divulged.

This manual is written in Italian. The Manufacturer is not responsible for any transcription

or translation errors.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Falmec Gruppo Incasso Pro in the language / languages: All languages as an attachment in your email.

The manual is 24,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Falmec Gruppo Incasso Pro Manual

Product: