Before cleaning or carrying out maintenance operations, disconnect the equipment by removing the plug or switching o the
main switch.
Regular maintenance guarantees proper operation and good performance over time.
Special attention is to be paid to the metal anti-grease filters and active carbon filters. In fact, frequent cleaning of the filters and their supports
ensures that no grease is accumulated on the hood, which is dangerous and can cause fires.
EXTERNAL CLEANING
You are advised to clean the external surfaces of the hood at least once every 15 days to prevent oily substances and grease from sticking to them.
Cleaning the hood, which is made of anti-fingerprint treated material (Fasteel), is to be carried out by only using water and neutral soap and a soft cloth.
Finish off cleaning by rinsing well and drying with soft cloths.
Do not use too much water next to the push button control panel and lighting devices in order to prevent humidity from reach-
ing electronic parts.
You must not use detergents containing abrasive, acid or corrosive substances or abrasive cloths: a direct consequence of not
complying with these warnings will result in irreversible deterioration of the hood's surface.
The Manufacturer declines all responsibility for failure to comply with these instructions.
It is possible to remove the external suction panel completely in order to facilitate its cleaning (refer to the instructions O on page 9).
CLEANING OF INTERNAL PARTS
It is forbidden to clean electrical parts, or parts related to the motor inside the hood, with liquids or solvents.
Do not use abrasive products.
All these operations are to be carried out after having disconnected the equipment from the electrical mains power supply.
METAL ANTIGREASE FILTERS
The metal anti-grease filters are there to contain suspended grease particles: deposited on the filters, these feed on any
flames released when cooking, generate unpleasant odours, and compromise the passage of air, thus reducing suction
performance of the hood.
For this reason, it is advised to frequently wash the metal filters (at leastonce a month) leaving them to soak in boiling
water and dish washing liquid for 1 hour, taking care not to bend them. Do not use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry before reassembling them.
Washing in a dishwasher is permitted, however, it may cause the filter material to darken: to reduce the possibility of this
problem from happening, use low-temperature washes (55°C max.).
Open the external suction panel to remove the metal anti-grease filters (refer to the instructions O on page 9), then operate the handle
(refer to the instructions
P on page 9). Carry out operations in reverse order to insert them.
ACTIVE CARBON FILTERS
Active carbon filters have the function of retaining odours in the air flow passing through them. The air, purified by running
many times through the filter, is recirculated into the kitchen.
Active carbon filters cannot be washed and are to be immediately replaced every 3-4 months (depending on the fre-
quency of use of the hood).
Dispose of the active carbon filters in compliance with the regulations in force in the country of use.
To replace the active carbon filters, open the external suction panel (refer to the instructions O on page 9), remove the metal anti-
grease filters (refer to the instructions
P on page 9) and follow the instructions Q on page 9.
DISPOSAL AFTER END OF USEFUL LIFE
This symbol on products and/or in accompanying documents means that electrical and electronic products used must not be disposed of with general do-
mestic waste. For personal treatment, recovery and recycling, you are kindly asked to take these products to designated waste collection points where they
will be accepted freely. Alternatively, in other countries, it is possible to take products back to the local dealer and purchase a new similar product. Proper
disposal of these products contributes to saving valuable resources and avoid potential negative effects on personal health and the environment, which
may be caused by inappropriate disposal of waste. You are kindly asked to contact your local authorities for further information regarding the designated
waste collection points nearest to you. Penalties for improper disposal of such waste can be applied in compliance with national regulations.
INFORMATION REGARDING DISPOSAL IN EU COUNTRIES
The EU Directive with regard to WEEE has been implemented differently by each nation, therefore, should you wish to dispose of this equipment, we advise
you to contact the local authorities or the dealer to ask for the correct method of disposal.
INFORMATION REGARDING DISPOSAL IN OTHER NONEU COUNTRIES.
This symbol is only valid in the European Union: if you wish to dispose of this product in other countries, we advise you to contact your local authorities or
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Falmec Exploit - island at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Falmec Exploit - island in the language / languages: All languages as an attachment in your email.
The manual is 19,84 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
