Manual Falmec Cielo (page 14 of 64) (All languages)

709756

Zoom out

Zoom in

1/64

operation and relative warnings.

After the stainless steel hood has been installed, it

will need to be cleaned to remove any residues re-

maining from the protection adhesive as well as any

grease and oil stains which, if not removed, can cause

irreversible damage to the hood surface. To properly

clean the unit, the manufacturer recommends using

the supplied moist wipes, which are also available

sold separately.

Insist on original spare parts.

INTENDED USE

The equipment is solely intended to be used to

extract fumes generated from cooking food in

non-professional domestic kitchens: any other

use is improper. Improper use can cause damage

to persons, things, pets and exempts the Manu-

facturer from any liability.

The equipment can be used by children over the age

of 8 and by persons with reduced physical, sensory

and mental abilities, or with no experience or knowl-

edge, as long as they do so under supervision or after

having received relative instructions regarding safe

use of the equipment and understanding of the dan-

gers connected to it.

Children are not to play with the equipment. Clean-

ing and maintenance by the user must not be carried

out by children without supervision.

USE AND CLEANING WARNINGS

Before cleaning or carrying out mainte-

nance operations, disconnect the equip-

ment by removing the plug or switching

o the main switch.

Do not use the hood with wet hands or bare feet.

Always check that all electrical parts (lights, extractor

fan) are oﬀ when the equipment is not being used.

The maximum overall weight of any objects placed

or hung (if applicable) on the hood must not exceed

1.5 Kg.

Always supervise the cooking process during the use

of deep-fryers: Overheated oil can catch ﬁre.

Do not leave open, unattended ﬂames under the

hood.

Do not prepare food over an open ﬂame under the

hood.

Never use the hood without the metal anti-grease

ﬁlters: in this case, grease and dirt will deposit in the

equipment and compromise its operation.

Accessible parts of the hood can be hot when used at

the same time as the cooking appliances.

Do not carry out any cleaning operations when parts

of the hood are still hot.

There can be a risk of ﬁre if cleaning is not carried out

according to the instructions and products indicated

in this booklet.

Disconnect the main switch when the equipment is

not used for long periods of time.

If other appliances that use gas or other fu-

els are being used at the same time (boiler,

stove, replaces, etc.), make sure the room

where the fumes are discharged is well-ventilat-

ed, in compliance with the local regulations.

INSTALLATION

only intended for qualied personnel

Before installing the hood, carefully read the chapter 'SAFETY

INSTRUCTIONS AND WARNINGS'.

TECHNICAL FEATURES

The technical speciﬁcations are exhibited on the labels located inside the hood.

POSITIONING

The minimum distance between the highest part of the cooking equip-

ment and the lowest part of the hood is indicated in the installation in-

structions.

Generally, when the hood is placed over gas cookers, the distance must be

at least 65 cm (25.6''). However, according to an interpretation of standard

EN60335-2-31 dated 11-07-2002 of TC61 (sub-clause 7.12.1 meeting 15 agenda

item 10.11), the minimum distance between the cooker and lower part of the

hood can be reduced to the quota reported in the installation instructions.

Should the instructions for the gas cooker specify a greater distance, this must

be taken into consideration.

Do not install the hood outdoors and do not expose it to outdoor environment

(rain, wind, etc.).

ELECTRICAL CONNECTION

(only intended for qualied personnel)

Disconnect the equipment from electrical mains power supply be-

fore carrying out any operations on the hood.

Ensure that the wires inside the hood are not disconnected or cut:

in the event of damage, contact your nearest Servicing Department.

Refer to qualied personnel for electrical connections.

Connection must be carried out in compliance with the provisions of law

in force.

Before connecting the hood to the electrical mains power supply, check that:

• voltage supply corresponds with what is reported on the data plate located

inside the hood;

• the electrical system is compliant and can withstand the load (see the techni-

cal speciﬁcations located inside the hood);

• the power supply plug and cable do not come into contact with tempera-

tures exceeding 70 °C;

• the power supply system is eﬀectively and properly connected to earth in

compliance with regulations in force;

• the socket used to connect the hood is within reach.

In case of:

• devices ﬁtted with cables without a plug: the type of plug to use is a ''stand-

ardised'' one. The wires must be connected as follows: yellow-green for earth-

ing, blue for neutral and brown for the phase. The plug must be connected to

an adequate safety socket.

• ﬁxed equipment not provided with a power supply cable and plug, or any

other device that ensures disconnection from the electrical mains, with an

opening gap of the contacts that enables total disconnection in overvoltage

category III conditions.

Said disconnection devices must be provided in the mains power supply in

compliance with installation regulations.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Falmec Cielo in the language / languages: All languages as an attachment in your email.

The manual is 17,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Falmec Cielo Manual

Product: