662004

Falmec Blade Wall Manual

19
Zoom out
Zoom in
Previous page
1/88
Next page
19
ENGLISH
24h
Speed 1 button
With LED on (speed 1 already running):
• Pressing this key will switch o the hood motor and the LED associated with the key
With LED o:
• A short press starts or sets the hood at speed 1 (the function starts when the key is released); when speed 1 is running, the relative
LED lights up.
• With the motor o, a long press (at least 3 seconds) will start the recirculation function: in this mode (for 24 hours), the hood runs an
operating cycle which involves starting the motor at the 1st speed for 1 hour, followed by 3 hours with the motor down. This cycle is
repeated for 24 hours, until timeout. For these 24 hours, the LED ashes, meaning that the recirculation function is running. With this
feature enabled, you CANNOT select other speeds.
• To deactivate this function, keep the relative key pressed for at least 3 seconds.
Speed 2 button
With LED on (speed 2 already running):
• Nothing will happen when this key is pressed. To switch the hood o rstly select speed 1, then press the "speed 1 button" again.
With the LED o and a speed on:
• Press the key (long or not) to set the hood on speed 2. When speed 2 is running the relative LED will light up.
With the LED o and NO speed on:
• Nothing will happen when this key is pressed.
Speed 3 button
With LED on (speed 3 already running):
• Nothing will happen when this key is pressed. To switch the hood o rstly select speed 1, then press the "speed 1 button" again.
With the LED o and a speed on:
• Press the key (long or not) to set the hood on speed 3. When speed 3 is running the relative LED will light up.
With the LED o and NO speed on:
• Nothing will happen when this key is pressed.
Speed 4 button
With LED on (speed 4 already running):
• Nothing will happen when this key is pressed. To switch the hood o rstly select speed 1, then press the "speed 1 button" again.
With the LED o and a speed on:
• Press the key (long or not) to set the hood on speed 4. When speed 4 is running the relative LED will start ashing; the 4th, or inten-
sive, speed is timed and after approximately 7 minutes the motor will automatically switch to 3rd speed.
With the LED o and NO speed on:
• Nothing will happen when this key is pressed.
Light Button
Light:
• By briey pressing the key (the back-lit button), you turn the light on and o.
LIGHTING
The hood has uorescent lamp lighting.
If the lamp ever needs to be replaced:
• disconnect the appliance from the electrical mains power supply by unplugging it or turning o the main switch;
• open the external suction panel (see instructions G on page 6);
Phase L page 6
• remove the covering element (N) (Fig.
1
and
2
);
• take out the blown uorescent tube (M) (Fig.
3
and
4
);
• put in a new uorescent lamp by performing, in reverse order, the operations described in Fig.
3
and
4
;
The new uorescent lamp must be identical to the old one!
• put the covering element back in (N) performing, in reverse order, the operations described in Fig.
1
and
2
;
• connect the appliance back up to the electrical power mains.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falmec Blade Wall at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falmec Blade Wall in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info