661994

Falmec Altair Island Manual

24
Zoom out
Zoom in
Previous page
1/80
Next page
22
Phase 2
- Hook the hood on the support bar.
- Adjust the alignment of the hood, using the fixing screws (Fig. 2): these can be reached by
opening panel (D) and removing anti-grease metal filters (E). The upper screw (B) adjusts the
distance from the wall, the lower one (C) the vertical scrolling.
- To prevent the hood from falling due to a pressure below, fasten it to the wall with two ex-
pansion bolts and relative screw via the appropriate holes (F) inside the hood.
Phase 3 (exhaust version only)
- To install the exhaust version hood, connect to the PVC tube (N) protruding from the hole
on the cover (G) of the hood. In case of discharge air from the rear, connect fitting (M) to a
suitable elbow shaped of flexible tube (Fig. 3); subsequently, place the cover in its original
position.
MIRA WALL HOOD ASSEMBLY (fixed or telescopic chimney)
Phase 1
- Place on the wall the support bar (A) (Fig. 1), at the same height of the cooker resulting from
the sum of the heights X+Y+320 mm (fig. 4).
- With a spirit level, verify the horizontal alignment and mark two drilling points at the edges
of bar n. 2.
- Drill, insert n. 2 expansion bolts of 8 mm and fasten the bar with the relative screws.
Phase 2
- Hook the hood on the support bar (Fig. 5).
- Adjust the alignment of the hood, using the fixing screws.
- The upper screw (B) adjusts the distance from the wall, the lower one (C) the vertical scrol-
ling.
Phase 3
- To prevent the hood from falling due to a pressure below, fasten it to the wall with an expan-
sion bolt and relative screw, using the appropriate holes on the hood rear.
- In case of exhaust version, connect the output fittings of the fan to the external discharge,
using a suitable tube (see fig. 6).
- Carry out electric connection only after having disconnected the electric power supply of the
hood.
Phase 4
Mira with fixed chimney: join the chimney (G) to the hood body and fasten it using screws (V1).
Mira with chimney+telescopic extension: Place extension (H) in the chimney (G) and fasten
them to the body of the hood using the 8 screws (V1).
In case the hood is assembled with a kitchen shelf, use screws (V1) with suitable length. The
shelf must be properly fastened autonomously, so that it does not weight down the hood.
- Scroll the extension (H) until reaching the desired height. Once the right position is found (L),
verify the horizontal alignment with a spirit level and mark n. 2 drilling points at the edges.
- Drill, insert n. 2 expansion bolts of 4mm ø and fasten the bracket (L) with the relative screws.
- Tighten the extension (H) to the bracket (L) using screws (M).
- Power the hood complying with the regulations in force (sec. D).
ASSEMBLY INSTRUCTIONS OF ALTAIR/MIRA ISLAND
Phase 1
- Due to packaging and transport requirements, the hood is provided with an extension and
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falmec Altair Island at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falmec Altair Island in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info