709883
15
Zoom out
Zoom in
Previous page
1/40
Next page
15
a
d
c
b
The control panel displays [ L ] :
Refer to the chapter control panel locking page.
One or all cooking zone cut-off :
The safety system functioned.
You forgot to cut-off the cooking zone for a long time.
One or more sensitive keys are covered.
The pan is empty and its bottom overheated.
The hob also has an automatic reduction of power level and breaking Automatic
overheating
Continuous ventilation after cutting off the hob :
This is not a failure, the fan continuous to protect the electronic device.
The fan cooling stops automatically.
The automatic cooking system doesn’t start-up :
The cooking zone is still hot [ H ].
The highest power level is set [ 9 ].
The control panel displays [ U ] :
Refer to the chapter “Keep warm“.
The control panel displays [ II ]:
Refer to the chapter “Pause “.
The control panel displays [ ]:
Refer to the chapter “Bridge“.
When the symbol [ E 4 ] appears :
The table must be reconfigured. Please implement the following steps :
I) Important : before you start, make sure there is no more pot on the hob
II) Disconnect the appliance from the grid by removing the fuse or turning the circuit
breaker off
III) Reconnect the table to the grid
IV) Procedure :
* take a pot with a ferromagnetic bottom and a minimum diameter of 16 cm
* start the procedure within 2 minutes after reconnecting the hob to the grid
* don’t use the [ ] touch
V) First step : cancel the existing configuration
1) Press the touch n°2 and hold down
2) The symbol [ - ] will appear on each display
3) With your other hand, press successively and
quickly (less than 2s) on each [ - ] display.
Begin from the front right side and turn contrary
clockwise, as described on the picture
(from a to d).
A double "beep" means an error occured. If so, start again from item 1).
4) Remove your fingers from the touch control, then push again on touch 1 during few
seconds, until blinking [ E ] symbols appear.
5) Wait until [ E ] symbols stop blinking.
6) After few seconds, [ E ] are automatically transformed in [ C ]. The existing setup
has been cancelled.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falmec 105095101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falmec 105095101 in the language / languages: English, Italian as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info