605191

FALLER 120242 Ausschlackanlage mit Servoantrieb Manual

10
Zoom out
Zoom in
Previous page
1/16
Next page
10
Der Hebel (Pos. f) steht nun auf 0 bis -90°.
Den 1. Haltepunkt (Hebel oben!) mittels Steuerung 180725 programmieren. Dann die 2. Halteposition programmieren.
Reicht das Bewegungsfeld in eine der beiden Richtungen nicht aus, muss der Hebel umgesteckt werden.
The lever (Item f) is now standing over the range 0 to -90°.
Programme the 1st hold point (lever upwards!) using Control 180725. After that, programme the 2nd hold position.
If the rotation range is not sufficient in one of both directions, you will have to change the plugging position of the lever.
Le levier (Rep. f) se trouve à présent sur la zone 0 à -90°. Ensuite, programmer la 2ème position d’arrêt.
Programmer le 1er point d’arrêt (levier en haut !) au moyen de la commande 180725.
Si la zone de déplacement ne suffit pas dans l’une des deux directions, il faut changer l’emboîtement du levier.
De hendel (positie f) staat nu op 0 tot 90°. Dan de 2e stoppositie programmeren.
De 1e stopplaats (hendel boven) middels de aandrijving 180725 programmeren.
Als de bewegingsuitslag in een van beide richtingen niet goed is, moet de hendel worden omgestoken.
Das Zahnrad des Micro Servos (Art. Nr. 180726) darf nicht von Hand bewegt werden!
Den Hebel entsprechend dem Bild umstecken.
The toothed wheel of the Micro Servo (Art. no. 180726) may not be moved by hand!
Change the plugging position of the lever according to the picture.
On ne doit pas faire tourner à la main la roue dentée du Servomoteur Miniature (Réf. 180726) !
Change the plugging position of the lever according to the picture.
Het tandwiel van de micro servo’s (art. nr. 180726) mag niet met de hand worden bewogen!
De hendel conform de afbeelding omsteken.
Inhalt Tüte
Contents bag
Contenu sachet
Inhoud zakje
1. Haltepunkt
1st. hold point
1. point d’arrêt
1. Stoppositie
Ganz einschrauben, aber nicht festziehen.
Fully screw in, but do not tighten firmly.
Visser complètement, mais ne pas bloquer.
Schroeven aandraaien, maar niet vastdraaien.
2. Haltepunkt
2nd. hold point
2. point d’arrêt
2. Stoppositie
1. Haltepunkt
1st. hold point
1. point d’arrêt
1. Stoppositie
2. Haltepunkt
2nd. hold point
2. point d’arrêt
2. Stoppositie
h
f
g
h
g
i
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for FALLER 120242 Ausschlackanlage mit Servoantrieb at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of FALLER 120242 Ausschlackanlage mit Servoantrieb in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info