1. Das Zahnrad des Micro Servos (Art. Nr. 180726) darf nicht von Hand bewegt werden!
The toothed wheel of the Micro Servo (Art. no. 180726) must not be moved by hand!
On ne doit pas faire tourner à la main la roue dentée du Servomoteur Miniature (Réf. 180726) !
Het tandwiel van de micro servo’s (art. nr. 180726) mag niet met de hand worden bewogen!
2. Den Servo mittels Steuerung 180725 gegen den Uhrzeigersinn bis zum Anschlag (1. Halteposition) drehen. Dann die 2. Halteposition programmieren.
Make the Servo rotate counterclockwise, using Control 180725, up to the limit stop (1st hold position). After that, programme the 2nd hold position.
Faire tourner le servomoteur, au moyen de la commande 180725, dans le sens antihoraire jusqu’à la butée (1ère position d’arrêt). Ensuite, programmer la 2ème position d’arrêt.
De servo met behuulp van de besturing 180725 tegen de wijzers van de klok in tot de aanslag (eerste stoppositie) draaien. Dan de 2e stoppositie programmeren.
3. Durch Umstecken von Teil 9/6 kann die Position des Bewegungsfeld geändert werden.
By changing the plugging position of part 9/6, you can change the position of the rotation range.
En changeant l’emboîtement de la pièce 9/6, on peut changer la position de la zone de déplacement.
Door het omsteken van deel 9/6 kan de positie van de bewegingsuitslag worden gewijzigd.
Servosteuerung kann gesteuert werden mit:
- Schalter/Reedsensoren/Kontaktgleis
(mit/ohne automatischer Rückstellung)
- Digitalzentrale
- Automatik (Dauerlauf)
- CS 3.0 Erweiterungsmodul
The servo control can be triggered using:
- Switch/Dry-reed sensors/Switching track
(with or without automatic return)
- Digital control unit
- Automation (Permanent working)
- CS 3.0 Extension module
La commande du servomoteur peut s’actionner au moyen de:
- Interrupteur/Capteurs à lames souples/Voie à commutation
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for FALLER 120232 Dampfkran at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of FALLER 120232 Dampfkran in the language / languages: English, German, Dutch, French as an attachment in your email.
The manual is 2,52 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
