500344

Falcon Toledo XT 110 Manual

51
Zoom out
Zoom in
Previous page
1/60
Next page
51
WARNING  SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
14. To Change Oven Door Latch
Remove outer door panel (see 13). Remove screws ‘B’
holding latch assembly to inner door panel. Fit new catch
and reassemble in reverse order.
Check correct door operation.
15. To Adjust an Oven Door Catch Keep
Open oven door, slacken off locknut at base of keep, and
screw in or out as required until required fi t is obtained.
Retighten locking nut.
16. To Change Oven Door Seal
Open oven door. The seal is held in place by small hooks on
the rear face. At the corner pull seal diagonally away from
the door centre until that hook is released. Proceed to the
next hook and release it in a similar way, and so on. Use
force if the hooks are stiff , as the old seal will be discarded.
When fi tting new seal, position the seal join at the bottom.
Hook the new seal in one of the corner holes of the door,
and proceed round the door snapping in each hook in turn.
17. To Change Ignition Generator
Disconnect from electricity supply.
Pull cooker forward to gain access to the cover box at the
rear of the cooker. Remove the screws securing the cover
and lift clear. Pull off all the leads to the generator noting
their positions. Slacken the two screws holding generator to
cooker and remove generator.
Fit new generator to cooker and replace leads. Reassemble
in reverse order. Refer to wiring diagram. Check ignition
performance.
18. To Remove the Hotplate Electrode Leads
Disconnect from the electricity supply.
Pull the unit forward to access the rear of the appliance.
Remove the hotplate - see 2. Remove the cover box and
disconnect all HT leads at the generator. Disconnect the
lead at the electrode. Pull the sleeved bundle of HT leads
up through the rear upright. Pull the appropriate lead from
the sleeve and push in the replacement. Replace the leads
in the rear upright. Re-connect the leads at the generator
and oven electrode. Re-assemble in reverse order and check
ignition.
19. To Remove Oven Inner Back
Open the oven door. Remove oven furniture. For the LH
oven unscrew the 2 thermostat phial fi xing screws.
Remove the fi xings that secure the inner back to the oven
rear.
Lift the removable panel away. Re-assemble in reverse order.
Ensure that the retaining fi xings are fully tightened. For
the LH oven unscrew the 2 thermostat phial fi xing screws.
Remove the screws that secure the inner back to the oven
rear. Lift the removable panel away. Re-assemble in reverse
order. Ensure that the retaining fi xings are fully tightened.
20. To Replace an Oven Fan
Disconnect from the electricity supply.
Pull the unit forward to access the cover boxes at the rear of
the appliance. Remove the fi xings that secure the cover and
lift it clear. Remove the fan wiring, noting the connection
positions. Remove the inner back as detailed in Section 21.
Hold the fan blades and undo the centre nut (LH thread),
brass washers, fan blade and circlip. Undo the fi xings that
retain the fan and remove it from the cavity rear. Fit the
replacement and re-assemble parts in reverse order. Check
that the oven operates satisfactorily.
… 51 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon Toledo XT 110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon Toledo XT 110 in the language / languages: English, French as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info