324671
55
Zoom out
Zoom in
Previous page
1/60
Next page
55
WARNING  SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
15. To Change Oven Door Latch
Remove outer door panel (see 14).
Remove screws ‘B’ holding latch
assembly to inner door panel. Fit new
catch and reassemble in reverse order.
Check correct door operation.
16. To Adjust an Oven Door Catch Keep
Open oven door, slacken off locknut at base of keep, and screw in
or out as required until required fi t is obtained. Retighten locking
nut.
17. To Change Oven Door Seal
Open oven door.
The seal is held
in place by small
hooks on the rear
face. At the corner
pull seal diagonally
away from the door
centre until that
hook is released.
Proceed to the next hook and release it in a similar way, and
so on. Use force if the hooks are stiff , as the old seal will be
discarded.
When fi tting new seal, position the seal join at the bottom. Hook
the new seal in one of the corner holes of the door, and proceed
round the door snapping in each hook in turn.
18. To Remove Grill Element.
Disconnect from electricity supply.
Remove grill pan from grill chamber. From inside grill
compartment remove enamelled front shield from grill roof, 2
screws and washers. Remove 2 screws and washers securing the
grill element front support. Remove the screws from the grill
elements.
Lift elements out carefully, disconnect the leads from the element
terminals noting their position. If it is not possible to disconnect
the leads in this way, pull cooker forward to gain access to the
rear, remove screws securing the electric cover to the back sheet
and remove cover and disconnect the terminals from the rear.
Fit new elements, reassemble in reverse order. Check operation
of grill.
19. To Remove a Main Oven Inner Back.
Open RH oven door and remove the screws and washers securing
the inner back to the back of the oven.
Carefully lift away the inner back. Reassemble in reverse order
making sure that the 4 screws and washers are fully tightened.
20. To Change a Main oven Fan.
Disconnect from electricity supply.
Pull cooker forward to gain access to the rear. Remove screws
securing the electric cover to the back sheet and remove cover.
Disconnect the 3 terminals connected to the fan noting their
position. Remove oven inner back (see 20). Hold the fan blade
and remove the centre nut (left hand thread) 2 brass washers, fan
blade and Circlip. Unscrew fan retaining nuts and washers (3 off
each) and lift the fan away from the rear of the cooker. Fit new fan
and reassemble in reverse order. Check operation of oven.
21 To Remove an Oven element Thermal Cut-Out.
Disconnect from the electricity supply.
Pull the cooker for ward to gain access to the cover box. Undo
the cover screws and lift clear. The cutout is located on the earth
plate be side the oven element con nec tions. Disconnect the
cutout wir ing. Undo the fi xings that secure the cutout to the
earth plate and re move. Fit re place ment control and re-as sem ble
in reverse order.
22. To Remove a Main Oven Fan Element.
Disconnect from electricity supply.
Remove oven inner back (see 19).
Remove 2 screws from the top of the element and 1 from the
bottom of the element in side the oven. Lift element out carefully,
disconnect the terminals connected to the element noting their
positions. If it is not possible to disconnect the leads in this way,
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon excel at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon excel in the language / languages: English, German as an attachment in your email.

The manual is 2,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info