500337
45
Zoom out
Zoom in
Previous page
1/76
Next page
45
English
12 To Remove a Hotplate Burner Spark
Electrode
a) Remove the pan supports, hotplate accessories
and burner heads.
b) Undo the bezel venturi and remove the bezel from
the hotplate. The spark ignition wire will be pulled
through the electrode clearance hole.
c) Disconnect the spark electrode from the ignition
wire.
Note
Take care to prevent the ignition wire from falling
back through the clearance hole.
d) Undo the spark electrode from the bezel by
removing the spring clip and spring.
e) Fit the replacement electrode to the burner bezel.
Ensure that the spring and clip are properly
located.
f) Replace in reverse order and check correct burner
ignition.
13 To Remove a Hotplate Burner
a) Remove the pan supports, hotplate accessories
and burner heads.
b) Remove the hotplate as detailed in Section 2.
c) Remove the nut that secures the burner body to
the support channel.
d) Remove the fixings that secure the support
channel to the chassis. Lift the channel clear of the
appliance.
e) Undo the compression fitting which connects the
burner body to the gas pipe. Remove the burner
body from the appliance.
f) Replace in reverse order. Check the appliance is
gas sound and that the burner operates
satisfactorily.
14 To Remove the Oven Door
a) Open the oven door.
b) Support the door and remove the two screws
which secure the upper hinge to the front frame of
the unit.
c) Remove the door from the lower hinge by lifting
slightly and moving it outward.
d) Re-assemble in reverse order.
15 To Remove the Grill Door
a) Remove the pan supports, hotplate accessories
and burner heads.
b) Remove the hotplate as detailed in Section 2.
c) Remove the control panel as detailed in Section 3
d) Remove LH side panel a detailed in Section 4.
e) Remove the kicker plate (4 screws).
f) Remove the central vertical cover situated between
the ovens. (5 screws).
g) Remove the 2 countersunk screws (1 per side)
which secure the hinge arms to the front of the grill
chamber.
Note
The door hinge arms are spring tensioned. Carefully
remove the grill door and retain the gaskets.
h) Re-assemble in reverse order. Ensure that the
gasket is fitted between the hinge arm and the front
of the grill chamber. Check door operation.
16 To Remove the Oven Outer Door Panel
a) Open the oven door.
b) Remove two screws ‘A’ and two screws ‘B’ from
the door.
c) Remove the outer door panel.
d) Undo the nuts that secure the handle to the door
panel. Fit the handle to the replacement door
panel.
e) Fit the replacement panel to the oven inner door.
f) Re-assemble in reverse order.
17 To Remove the Door Latch
a) Remove the oven outer door panel as detailed in
Section 16.
b) Remove the fixings that secure the latch assembly
to the inner door panel.
c) Fit the replacement catch and re-assemble in
reverse order.
d) Check correct operation of door.
18 To Remove the Oven Door Seal
a) Open oven door. The seal is held in place by small
hooks on the rear face. At the corner pull seal
diagonally away from the door centre until that
hook is released.
b) Proceed to the next hook and release it in a similar
way, and so on. Use force if the hooks are stiff, as
the old seal will be discarded.
c) When fitting new seal, position the seal join at the
bottom. Hook the new seal in one of the corner
holes of the door, and proceed round the door
snapping in each hook in turn.
19 To Adjust the Oven Door Catch Keeper
a) Open the oven door and slacken the locknut at the
keeper base.
b) Adjust the keeper inward or outward as required,
until the desired door operation is obtained.
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon De Luxe 1092 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon De Luxe 1092 in the language / languages: English, German, French as an attachment in your email.

The manual is 1,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Falcon De Luxe 1092

Falcon De Luxe 1092 Usermanual and installation guide - Dutch - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info