500343

Falcon De Luxe 1000DF Manual

16
Zoom out
Zoom in
Previous page
1/56
Next page
16
English
Positioning the Cooker
The diagrams show the minimum recommended
distance from the cooker to nearby surfaces.
The 3mm gaps each side are to allow for moving the
cooker
The hotplate surround should be level with, or above,
any adjacent work surface. Above hotplate level a gap
of 75mm should be left between each side of the cooker
and any adjacent vertical surface.
For non-combustible surfaces (such as unpainted metal
or ceramic tiles) this can be reduced to 25mm.
A minimum space of 800mm is required between the top
of the hotplate and a horizontal combustible surface.
Any cooker hood should be installed in accordance with
the hood manufacturer’s instructions.
Surfaces of furniture and walls at the sides and rear
of the appliance should be heat, splash and steam
resistant. Certain types of vinyl or laminate kitchen
furniture are particularly prone to heat damage and
discolouration. We cannot accept responsibility for
damage caused by normal use of the cooker to any
material that de-laminates or discolours at temperatures
less than 65°C above room temperature.
For safety reasons curtains must not be fi tted
immediately behind the cooker.
We recommend a gap of 1006mm between units to
allow for moving the cooker. If a fl ush fi t is required, fi t
the cooker up to the unit at one side then fi t the unit the
other side.
Unpacking the Cooker
Do not take any packaging off the cooker until it is
directly in front of the place it is to be installed (unless it
will not fi t through a door in its outer packaging).
Moving the Cooker
The cooker is very heavy. Take great care.
We recommend two people manoeuvre the cooker.
Remove all the doors by opening the door fully, then
rotate the hinge locking disc 90° clockwise on both door
hinges to lock door in open position.
Carefully close door and at approximately half closed the
hinges will release themselves from the cooker frame.
hinge
location
slot
original
position
locked
position
slotted
disc
hinge quadrant
Carefully put the doors in a safe place.
Ensure that the fl oor covering is fi rmly fi xed, or removed
to prevent it being disturbed when moving the cooker
around. You will need the levelling tool.
From the front tilt the cooker backwards and remove the
front half of the polystyrene base pack.
Repeat from the back and remove the rear half of the
poly base.
The cooker has three base rollers. The hexagonal
adjusters are positioned as shown below.
Fit the levelling tool on the a hexagonal adjusters as
shown below.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon De Luxe 1000DF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon De Luxe 1000DF in the language / languages: English, French as an attachment in your email.

The manual is 5,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info