326872

Falcon 900 deluxe inox Manual

23
Zoom out
Zoom in
Previous page
1/32
Next page
23
Conversion to LP
If the appliance is to be converted to LP gas do the
conversion at this point. See the conversion section
of these instructions.
Levelling
You are recommended to use a spirit level on a shelf
in one of the ovens to check for level.
Place the cooker in its intended position taking care
not to twist it within the gap between the kitchen units
as damage may occur to the cooker or the units.
The front feet and rear rollers can be adjusted to
level the cooker. To adjust the height of the rear of
the cooker use the levelling tool supplied to turn the
adjusting nuts at the front bottom corners of the
cooker. To set the front feet turn the bases to raise
or lower.
Gas Connection
Fitting a stability bracket
A stability bracket or chain (not supplied by with
the cooker) should be fitted when the cooker is
connected to a flexible gas supply. Any restraining
device should be secured to the fabric of the building
and should be able to be released so that the cooker
can be pulled out for cleaning and maintenance.
When fitting a stability bracket read these
instructions together with the leaflet supplied with the
bracket.
a) Position and level the appliance.
b) Draw a pencil line 70mm from the front edge of
the levelling feet.
c) Mark off 350mm from the RH side of the unit to
indicate the centre line for the bracket.
d) Remove the range.
e) Mark off 500mm to locate the front edge of the
lower bracket. Fix bracket to floor.
f) Measure the height from floor level to the top
edge of the rear channel. Add 3mm to this
dimension and assemble the stability bracket to
this height (i.e. from floor level to underside of top
member)
Gas Connection
The Gas supply needs to terminate with a down
facing bayonet. The rear cover boxes limit the
position of the supply point.
view from the rear
A position for gas supply connector
B appliance gas inlet
Because the height of the cooker can be adjusted
and each connection is different it is difficult to give
precise dimensions. Ideally the house supply
bayonet should be in the shaded area shown in the
diagram. Although a 900mm hose can be used, a
1250mm hose will allow slightly more flexibility in the
positioning of the bayonet and make moving the
cooker easier. The hose should be fitted so that both
inlet and outlet connections are vertical so that the
hose hangs downwards.
The hose should be fitted so that both inlet and outlet
connections are vertical so that the hose hangs
downwards in a ‘U’ shape.
For Natural Gas the flexible hose must be in
accordance with B.S.669.
For LP Gas it should be capable of 50mbar
pressure, 70C temperature rise and carry a red
stripe, band or label.
If in doubt contact, your supplier.
Screw connect the threaded end of the hose into the
gas inlet in the underside of the connector block on
the back of the cooker.
After completing the gas connection, check the
cooker is gas sound with a pressure test. When
checking for gas leaks do not use washing up liquid -
this can corrode. Use a product specifically
manufactured for leak detection.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon 900 deluxe inox at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon 900 deluxe inox in the language / languages: English as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Falcon 900 deluxe inox

Falcon 900 deluxe inox User Manual - German - 30 pages

Falcon 900 deluxe inox User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info