500342
27
Zoom out
Zoom in
Previous page
1/36
Next page
SERVICING  WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
27
Conversion to LP Gas
Servicing - warning
This conversion must be performed by a competent
person. After conversion the installation must comply
with the relevant regulations and also the local electricity
supply company requirements. Read the instructions
before converting this appliance.
Failure to convert the appliance correctly could invalidate
any warranty or liability claims and lead to prosecution.
This instruction must be used in conjunction with the rest
of the appliance instruction, in particular for information
on Standards, cooker positioning, connection hose
suitability etc.
When servicing or replacing gas-carrying components
disconnect from gas before commencing operation and
check appliance is gas sound after completion.
Do not use re-conditioned or unauthorised gas controls.
Conversion
Disconnect from electricity and gas before servicing.
Check appliance is safe when you have fi nished.
This appliance is CAT II 2H3+. It is supplied set for G20
natural gas at 20millibar
A conversion kit for LP gas is supplied with the cooker.
Injectors
Remove pan supports and burner heads.
Burner head
Brass venturi
Burner base
Burner ring
Undo the large brass nuts and remove the brass venturis
and brass rings.
Either:-
Use a long box spanner to access and remove the
old jets.
Or: -
Lift up the front of the hotplate top and prop it up.
The burner bases are now accessible - remove the
old jets.
Save the jets removed from the appliance for possible
future use. Fit the new jets; see the table for the correct
type.
If you have lifted up the hotplate then carefully replace
it taking care not to damage or displace the ignition
electrodes or fl ame safety probes (arrowed) and replace
the rear fi xing screws.
To convert the control taps
Pull off all the control knobs.
Open the oven door & grill door and remove the fi xing
screws underneath the control panel.
Remove the 3 fi xing screws at the top of the control panel.
Pull the control panel forward. Rest it on the open grill
door and the open right hand oven door
The tap bypass screw is now accessible. Unscrew the tap
bypass screw.
Using a pair of long nose pliers carefully remove the
bypass screw and fi t the correct replacement screw. See
table for correct size. Tighten the screw down.
Repeat for all the burner control taps.
Refi t the control panel.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon 1092 CT Dual Fuel at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon 1092 CT Dual Fuel in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info