752971
6
Zoom out
Zoom in
Previous page
1/128
Next page
6
4.
CONTROLS
A B C D E
Button Function Led
ATurns the motor on/off at speed one. On/Off.
This button is always lit when the
Hood is in operation.
Press and hold the button for approximately 2 seconds, with all the
loads turned off (Motor and Lights) to perform a Reset if the Filter
Alarm is Activated.
Flashes 3 times.
With the motor turned off:
Saturationofthegreaselterstakesplaceafter100hoursofcontinuous
operation of the hood.
Flashes once a second.
With the motor turned off:
Saturationoftheactivatedcharcoallterstakesplaceafter200hours
of continuous operation of the hood.
Flashes once every 0.5 seconds.
BTurns the Motor on at speed two. On/Off.
Press and hold the button for approximately 2 seconds, with all the
loads turned off (Motor+Lights), to turn the Activated Charcoal Filter
alarm on. The relevant LED (A)ashestwice toconrm.
To turn the alarm off, press the button again and hold for at least 2
seconds. The relevant LED (A)ashesonce.
-
CTurns the Motor on at speed three. On/Off.
Press and hold for approximately 2 seconds to activate/deactivate
ECO mode. This function turns the motor on at speed one and effects
one 10 minute extraction every hour for 24h. It can also be turned
off by pressing button (A).
Green light on.
DTurns the motor on at speed INTENSIVE 1.
This speed is timed to run for 10 minutes. At the end of this time,
the system returns automatically to the speed that was set before. If
it is activated with the motor turned off, the hood will switch to OFF
at the end of the time.
To turn it off, press button (D) or button (A) again.
Flashes every second.
Press and hold for approximately 2 seconds to turn the motor on at
speed INTENSIVE 2.
This speed is timed to run for 6 minutes. At the end of this time, the
system returns automatically to the speed that was set before. If it
is activated with the motor turned off, the hood will switch to OFF
at the end of the time.
Press and hold button D or button A for approximately 2 seconds to
deactivate the function.
Flashes every half second.
ETurns the lights ON/OFF at maximum strength. On/Off.
Press and hold the button for approximately 2 seconds, with all the
loads turned off (Motor and Lights), to turn the Remote control On/Off.
1 flash of LED (A) - Remote
control Off.
2 ashes of LED (A) - Remote
control On.
5. LIGHTING
For replacement contact technical support
(“To purchase contact technical support”).
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Faber Onyx-V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Faber Onyx-V in the language / languages: All languages as an attachment in your email.

The manual is 22,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Faber Onyx-V

Faber Onyx-V Installation Guide - All languages - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info