695739
15
Zoom out
Zoom in
Previous page
1/44
Next page
Installation Instructions Installation Instructions
15
4.4.1 Hanging on the wall 800/500-650-IIL, -IIR and -III
The appliance can be wall-mounted with the optional wall bracket
(see g. 1.8).
4.5 Installing the ue materials
When penetrating a non-combustible wall or ceiling the
opening must be at least 5mm larger than the diameter of the
discharge material. At a combustible wall or ceiling is this
100mm larger than the diameter of the drainage material.
Horizontal sections should be installed with a slope towards
the re (3 degrees).
Build the system from the re. If this is not possible you can
make use of an extendable adapter section.
For truing up the exhaust system use the 0,5m. pipe, which
can be shortened and ensure that the inner pipe is always
2cm longer than the outer pipe.
Parts, which are shortened, must be secured with a
self-tapping screw.
Wall and roof terminals can also be cut.
Do not insulate but ventilate built-in ue material (approx.
100cm²).
4.6 Constructing the false chimney
If possible, carry out a performance test at the re before nally
nishing the installation.
4.6.1 False chimney
* Construct the false chimney of non-combustible material in
combination with metal proles or of masonry/concrete
blocks.
* Be aware of ventilation grids and service door (see g. 1.0 to
1.5). Place above the ventilation grids a screen plate made of
non-combustible material (see g. 1.1, 1.3 or 1.5)
* Always use a lintel or reinforcing bars while bricking the
outlet. They should not be placed directly on the re.
* Built the false chimney against the appliance (see g. 1.0 to
1.5). Keep a minimum distance of 2mm between the false
chimney and the appliance, because of the extension of the
appliance.
4.6.2 Installation and nishing
For installation and nishing the following points are of interest:
H = moldings (g. 2.4 and 2.7)
I = distance prole (g. 2.4)
J = upper side ange combustion chamber (g. 2.5)
K = distance holder/glass support (g. 2.6)
L = distance holder/glass support (g. 2.6)
> Please note:
Ensure that the re is not load-bearing with regard to the false
chimney breast.
4.6.3 Method I with cover strip (g. 2.2)
Build the false chimney breast or plateau against the moldings H
and distance proles I (see g. 2.4 and 2.7).
Keep a minimum distance of 2mm between the false chimney and
the appliance, because of the extension of the appliance. Take into
account the thickness of the nish!
4.6.4 Method II with built-in strip (g. 2.3)
Remove the distance proles “I” (see g. 2.4).
Make sure that the screws of the front distance prole “I” will be
replaced, in order to ensure the air tightness of the appliance.
Build the plateau against the glass supports K and L (see g. 2.6).
Keep a minimum distance of 2mm because of the extension of the
appliance.
For the height of the plateau see point “J” (g. 2.5).
5 Removing the glass
5.1 Removing the glass from the front
MatriX 800-I:
Remove the moldings “A” left and right (g. 3.0).
Turn the left and right side clamps “B” up (g. 3.0).
Place the suction cups on the glass and slide the upper list
“C” up (g. 3.1).
See g. 3.2, number:
1. Slide the glass to the top so that the bottom will
release.
2. Now, carefully slide the glass to the left.
3. Get the released side towards to you and put the glass
on a safe place.
MatriX 800-II:
Remove molding “A” left or right (g. 3.0).
Turn the left or right side clamps “B” up (g. 3.0).
Place the suction cups on the glass and slide the upper list
“C” up (g. 3.3).
See g. 3.3, number:
1. Slide the glass to the top so that the bottom will
release.
2. Now, carefully slide the glass to the left or to the right.
3. Get the released side towards to you and put the glass
on a safe place.
MatriX 800-III:
Place the suction cups on the glass and slide the upper list
“C” up (g. 3.3).
See g. 3.3, number:
1. Slide the glass to the top so that the bottom will
release.
4. Get the released side towards to you and put the glass
on a safe place.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Faber MATRIX 800-650 II at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Faber MATRIX 800-650 II in the language / languages: English as an attachment in your email.

The manual is 12,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Faber MATRIX 800-650 II

Faber MATRIX 800-650 II Installation Guide - German - 52 pages

Faber MATRIX 800-650 II User Manual - Dutch - 48 pages

Faber MATRIX 800-650 II Installation Guide - French - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info