752960
27
Zoom out
Zoom in
Previous page
1/32
Next page
27
EN 7
7
INSTALLATION
Fitting the Hood canopy
BEFORE FITTING THE HOOD TO THE WALL UNIT, PROCEED AS FOLLOWS:
Disconnect the wires to the Commands at the connectors.
Disconnect the wires to the Light at the con-
nectors.
The Hood can be installed directly on the
underside of the wall unit (Minimum 650 mm
from the Cooker Hob).
Create an opening in the bottom of the wall unit,
as shown.
Insert the hood until the side supports snap into
place.
Fasten using the 10 screws 12a provided.
Lock in position by tightening the screws Vf from
underneath the hood.
Open the suction panel by turning the specific knob.
Disconnect the panel from the hood canopy by sliding the
fixing pin lever.
Remove grease filters.
Screw the Frame into place
using the 6 screws 12f, re-
connect the wires to the
Commands and Light, re-
place the metal grease filter
and the Panel.
260
13
495 - 675
Système D'éclairage À Del
Les ampoules DEL doivent être remplacées par un
service d'entretien autorisé Faber.
Nettoyagedesltresàgraisse
métalliques
Les ltres à graisse métalliques peuvent
être lavés dans une solution d'eau chaude
savonneuse ou dans le lave-vaisselle. Ils
devraient être nettoyés tous les 2 mois, ou
plus fréquemment en cas d'utilisation parti-
culièrement intensive.
Retirez le ltre, en poussant simultanément
le levier vers l'arrière de l'appareil et en le
tirant vers le bas.
Lavez le ltre sans le plier. Laissez-le sécher
complètement avant de le réinstaller (un
changement de la couleur à la surface du
ltre au l du temps n'a aucun impact sur
son efcacité).
Remettez-le en place, en vous assurant que
la poignée se trouve vers l'avant.
Le lave-vaisselle pourrait ternir le ni du ltre
à graisse métallique.
Remplacementdultreàcharbon
actif
Les ltres à charbon actif ne sont pas
lavables et ne peuvent être régénérés. Ils
devraient être remplacés environ tous les
4 mois d'utilisation, ou plus souvent en cas
d'utilisation intensive.
Enlevez le ltre à charbon en le faisant
tourner dans le sens des aiguilles d'une
montre (vers l'arrière) jusqu'à ce qu'il se
dégage du carter du moteur, puis en le tirant
vers le côté.
Pour réinsérer les ltres à charbon, placez-
les sur le côté du ventilateur et poussez-les
vers l'intérieur. Tournez ensuite le ltre à
charbon dans le sens des aiguilles d'une
montre (vers l'avant) jusqu'à ce qu'il soit
bien installé.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Faber Classica Plus Clas 36 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Faber Classica Plus Clas 36 in the language / languages: English, French as an attachment in your email.

The manual is 4,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info