752946
7
Zoom out
Zoom in
Previous page
1/13
Next page
Version 7/11 - Page 7
Three Screws
Rangehood Body
Front
Strip
CUSTOMIZING YOUR RANGEHOOD
The front strip of the rangehood can be customized. The
front strip is attached to the rangehood by three recessed
screws and three key hole slots on the back side of the strip
as indicated in FIGURE 15. It is necessary only to remove
the three lower screws to remove the front strip. The top
screws will slide out of the key holes once the three lower
screws are removed.

The front strip dimensions are given in FIGURE 16. If you
wish to keep the frame of the front panel and only replace the
glass panel, the dimensions follow: Height = 5 11/16", Depth
= 1/8", Width = 29 11/16" (for 30" model) 35 11/16" (for 36"
model) 23 5/8" (for 24" model).
FIGURE 16
WIRING DIAGRAM
This rangehood uses Flourescent Lamp Type 18", 15W T8 and
Starter Type S2.
Rangehood Control Panel
All controls are located under the front panel and are shown in
FIGURE 17.

On/Off switch for the uorescent light. Moving the switch to the
1 Position turns the light On. Moving the switch to the 0 Position
turns the light Off.
FIGURE 15
FIGURE 17
FIGURE 18

Controls blower speed. Moving the switch to the 1 Position turns
the blower on LOW. Moving the switch to the 2 Position turns the
blower on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH.

Red light will be on when the rangehood is operating.

When the front panel of the rangehood is closed, the rangehood
will turn off by a microswitch. This turns the rangehood On and
Off without adjusting the switches for the Light or Blower and it
remembers the last speed setting.
Cleaning
The metal grease lters should be cleaned frequently in hot deter-
gent solution or placed in the dishwasher. Clean exterior surfaces
with hot soapy water. Using abrasives and scouring agents can
scratch rangehood nishes and should not be used to clean nished
surfaces.
Replacing the Fluorescent Light
To replace the uorescent light, remove the retainer clips from both
ends of the glass diffuser as indicated in FIGURE 18. Carefully
slide the glass diffuser all the way to the left. Lower the right end
of the glass below the support ange, then remove the glass by
sliding it back to the left. Replace the diffuser glass by reversing
these directions.
23 5/8" or 29 15/16" or 35 15/16"
5 7/8"
13/16"
USE AND CARE INFORMATION
This rangehood system is designed to remove smoke, cooking
vapors and odors from the cooktop area.
For Best Results
Start the rangehood several minutes before cooking to develop proper
airow. Allow the unit to operate for several minutes after cooking
is complete to clear all smoke and odors from the kitchen.
Blower On/Off

On/Off switch for the
blower. Moving the
switch to the 1 Posi-
tion turns the blower
On. Moving the switch
to the 0 Position turns
the blower Off.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Faber Agio 36BK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Faber Agio 36BK in the language / languages: English, French as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info