752941
5
Zoom out
Zoom in
Previous page
1/13
Next page
Version 7/11 - Page 5
PREPARE THE CABINET
1. Disconnect and move freestanding range from cabinet
opening to provide easier access to upper cabinet and rear
wall. Put a thick, protective covering over cooktop, set-in
range or countertop to protect from damage or dirt.
2. Determine and clearly mark with a pencil the center line
of the cabinet on the wall and on the underside of the cabinet
where the rangehood will be installed.
 The Agio attaches to the cabinet by four black screws.
Mark the cabinet and insert the screws into the underside
of the cabinet as shown in FIGURE 8. Do not tighten the
screws.
INSTALL THE RANGEHOOD
1. Remove the unit from the carton and place on a at
surface for assembly. Make sure to cover the surface to
prevent accidental damage. Remove all parts including the
Backdraft Damper, Screws, and Literature Package before
discarding the carton.
2. Remove both grease lters from the unit and set aside.
The rangehood is shipped from the factory with the backdraft
damper attached inside. Using a Phillips head screwdriver,
remove the backdraft damper by loosening the screw marked
with a red dot on top of the rangehood.
 Before installing, the rangehood must be adjusted for
venting. For ductless installations, read the following section
which discusses special requirements for these installations
before continuing.
For Horizontal or Vertical ducting, the respective exhaust
knockout must be removed. Each knockout is attached to the
rangehood by four points. Using a at blade screwdriver or
utility knife, remove the exhaust knockout. Save this plate as
it must be used to block the ductless exhaust grill. FIGURE
 shows the location of the knockouts for both horizontal
and vertical. ONLY ONE must be removed.
30" or 36" or 23 5/8" (60 cm)
30" or 36" or 23 5/8" (60 cm)
30" or 36" or 23 5/8" (60 cm)
FIGURE 7

FIGURE 8
4. Determine the proper cutouts for the ductwork. Make
all necessary cuts in the walls or cabinets for the ductwork.
Install the ductwork before mounting the rangehood.
5. Determine the proper location for the Power Supply
Cable. Both possible locations are given in . Use
a 1 1/4" Drill Bit to make this hole. Run the Power Supply
Cable. Use caulking to seal around the hole. DO NOT turn
on the power until installation is complete.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Faber Agio 24WH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Faber Agio 24WH in the language / languages: English, French as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info