752944
6
Zoom out
Zoom in
Previous page
1/13
Next page
Version 7/11 - Page 6
6. Reattach the control box and support. Make sure that
the wiring harness is concealed behind the support.
7. Remove the eld wiring compartment cover. Feed the
Power Supply Cable through the electrical knockout.
8. Attach the backdraft damper to the proper exhaust open-
ing using two silver screws supplied with the rangehood.
 Attach the rangehood to the cabinet bottom. The four
key holes slip onto the four screws mounted to the cabinet
bottom. Tighten the screws.
 Connect the Power Supply Cable to the rangehood.
Attach the White lead of the power supply to the White lead
of the rangehood with a twist-on type wire connector. Attach
the Black lead of the power supply to the Black lead of the
rangehood with a twist-on type wire connector. Connect
the Green (Green and Yellow) ground wire under the Green
grounding screw.
4. Remove the central support and control box by remov-
ing the screws indicated in FIGURE 11. It is not necessary
to remove the blower to perform this operation.
5. Attach the cover behind the exhaust grate with two silver
screws supplied with the rangehood as indicated in FIGURE 12.
11. Replace the eld wiring compartment cover. For duct-
less installations, refer to the next section which discusses
ductless installations. Replace the grease lters.
12. Turn the power supply on. Turn on blower and light.
IF THE RANGEHOOD DOES NOT OPERATE:
Check that the circuit breaker is not tripped or the
house fuse blown.
Disconnect the power supply and check that the
wiring connections have been made properly.
DUCTLESS INSTALLATIONS
For ductless installations, the blower must be positioned with
the exhaust pointing forward ( so that the exhaust exits from
the front grill ) before attaching the rangehood to the cabinet.
Ductless installations require Charcoal Filters.
1. Remove both grease lters, the central support and the
control box. Remove the two thumb screws on either side of
the blower and remove the blower from the mounting guides
as indicated in FIGURE 11.
2. 
.
Then Rotate the blower 180° so that the exhaust points out
the front of the rangehood. Replace the black lter holders
and the two thumb screws and tighten so that the blower
is securely fastened inside the rangehood as indicated in
. Reattach the control box and central support.
Make sure that the wiring harness is concealed behind the
central support.
 For ductless installations, Charcoal Filters are required
and must be installed before the grease lters are replaced.
The charcoal lters attach to both ends of the blower as
indicated in FIGURE 14.

FIGURE 11
FIGURE 12
FIGURE 14

A
A
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Faber Agio 24BK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Faber Agio 24BK in the language / languages: English, French as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info