706564

Faber ABN 15 Manual

16
Zoom out
Zoom in
Previous page
1/36
Next page
Symptom Cause Corrective Action
The fl ame effect will
not start.
Mains plug is not plugged in.
Switch A is in the ‘ON’ (I) position, but mode
Switch B has not been pressed. (See Fig.2)
Low water level.
Low voltage connector not connected
properly. (See Fig.8)
Check plug is connected to wall socket
correctly.
Press Switch B once for fl ame effect. (See
Fig.2)
Check the water tank is full and there is
water in the sump.
Check that the connector is inserted
correctly. (See Fig.8)
The fl ame effect is too
low.
Flame effect control knob is set too low.
(See Fig.2)
The water in the sump may be too high due
to the drawer being opened and closed
a number of times, water tank removed
a number of times, or the fi re has been
moved.
Metal Disc at the base of Sump might be
dirty (See Fig.13)
Increase level of fl ame by turning Control
knob C to the left slowly. (See Fig.2)
If water level in the sump is more than
40mm, the sump should be removed and
emptied in the sink.
Clean the Metal Disc with the soft brush
supplied. (See Fig.13) See ‘Maintenance.’ for
a step by step procedure.
Unpleasant smell
when unit is used.
Dirty or stale water.
Using unfi ltered tap water.
Clean the unit as described under
maintenance.
Use tap water with a maximum hardness of
10 dH only.
The fl ame effect has
too much smoke.
Flame effect setting is too high. Turn the fl ame effect Control knob C to the
right until it is at minimum and slowly turn to
the left, about ¼ a turn, at a time. Give the
fl ame generator some time to adjust before
increasing. (See Fig.2)
Main lamps are not
working and there are
no fl ames or smoke.
There is no water in the tank. Follow instructions under Maintenance, ‘Fill-
ing the water tank’.
Check the plug is connected to wall socket
correctly.
Switch ‘A’ Fig. 2 is in the ‘ON’ ( I ) position.
Press switch ‘B’ Fig.2 until you can hear one
beep only, for fl ame effect.
Water is leaking from
tank
Rubber seal in lid is damaged Refer to dealer for a replacement seal
Troubleshooting
10
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Faber ABN 15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Faber ABN 15 in the language / languages: English, German, Dutch, French, Norwegian as an attachment in your email.

The manual is 7,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info