706564

Faber ABN 15 Manual

13
Zoom out
Zoom in
Previous page
1/36
Next page
If you intend not using the appliance for longer than 2 weeks, drain the water from sump and water tank and
dry the sump.
Once installed, never move this fi re or lay on its back, without draining the water from sump and water tank.
The water tank, sump, sump lid, tank cap and air fi lters must be cleaned once every two weeks, particularly in
hard water areas.
The fi re appliance should never be operated if the lamps are not working.
The lamps should be regularly inspected as described under ‘Maintenance’ and ‘Changing lamps’.
Installation Instruction
Ensure that all packing items are removed (read any warning labels carefully).
Retain all packing for possible future use, in the event of moving or returning the appliance to your supplier.
To reduce heat losses and to prevent any chimney updraught affecting the operation of your fi re we
recommend that the chimney fl ue is blocked off, ensure that there is a slight gap for ventilation.
Insert bulbs fi rst before you connect to mains.
Bulbs in separate pack.
To install the appliance;
Hold the fi re by the sides of surround and gently manoeuvre into position. Plug the fi re into a 13amp/240 volt outlet.
Ensure that the supply cable exits at the front of the fi re, at the right or left hand corner to suit your supply socket
location and is not trapped under the fi re such that it might cause it to be damaged.
Before switching on the appliance, please read the following instructions.
Before using the manual controls fi rstly fi ll the water tank (See ‘Maintenance’, ‘Filling the water tank’).
Manual Controls
The manual controls are located behind the drawer.
(See Fig.2 for Manual Control lay out)
Switch ‘A’:- Controls the electricity supply to the fi re.
Note: This switch must be in the ‘ON’ ( I ) position for the fi re to operate with or without heat.
Switch ‘B’:- Controls the function of the fi re.
Press once to turn on fl ame effect. This will be indicated by one beep.
Although the main lights operate immediately it will take a further 30 seconds before the fl ame effect starts.
Press again to give fl ame effect and half heat. This will be indicated by two beeps.
Press again to give fl ame effect and full heat. This will be indicated by three beeps.
Press again to return to fl ame effect only.
This will be indicated by one beep.
Press to put fi re in to standby mode.
This will be indicated by one beep.
Control Knob ‘C’:- Controls the intensity of the fl ame effect.
Turning the control knob clockwise increases the fl ame effect, turning the control knob anti-clockwise will
decrease the fl ame effect.
When the water tank is empty the main lamps go out. See instructions under ‘Maintenance’, ‘Filling the water tank’.
When this procedure is complete, the main lamps will illuminate but it will take 30 seconds before the fl ames return.
Remote Control Operation
On the control panel, Switch A (see Fig.2) must be in the ‘ON’ ( I ) position in order for the remote control to operate.
There are 3 buttons on the remote control. (See Fig.7)
To operate correctly the remote must be pointed towards the front fuel effect.
The remote control functions are as follows:
Press once to turn on Flame effect only.
This will be indicated by one beep. (270 watt)
Press once to turn on Half heat and Flame effect.
This will be indicated by two beeps. (750 watt)
Press again to turn on Full heat and Flame effect.
This will be indicated by three beeps. (1500 watt)
Standby
This will be indicated by one beep.
Battery Information.
1. Unclip the battery cover on the back of the remote control. (See Fig.7)
2. Install AAA batteries into the remote control.
3. Replace the battery cover.
Discard leaky batteries.
Dispose of batteries in the proper manner according to provincial and local regulations.
Any battery may leak electrolyte if mixed with a different battery type, if inserted incorrectly, if all the batteries are
not replaced at the same time, if disposed of in a fi re, or if an attempt is made to charge a battery not intended to be
recharged.
7
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Faber ABN 15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Faber ABN 15 in the language / languages: English, German, Dutch, French, Norwegian as an attachment in your email.

The manual is 7,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info