811697
35
Zoom out
Zoom in
Previous page
1/40
Next page
35ENGLISH
Displays
Display Reason
off Generator o
sTaRT The start-up phase is in progress
pelleT loaDinG Continuous pellet loading is in progress during the ignition phase
iGniTion The ignition phase is in progress
pRepaRaTion The preparation phase is in progress
WoRk The normal work phase is in progress
MoDulaTion The generator is working at minimum
final cleaninG The nal cleaning is in progress
sTanD-by Generator o waiting for re-ignition due to the external thermostat.
coolinG
sTanD by
A new ignition is attempted when the generator has just been switched o. When the generator switches o, you must
wait for the complete shutdown of the fumes motor, then clean the burn pot. The generator can only be re-ignited when
these operations have been performed.
black ouT
sTanD by
The generator is cooling after a power cut.
Once cooling is completed, it will re-start automatically
auTo bloW The automatic blow is active
close
HoppeR-sToVe DooR
This indication means that you have 60 seconds to close the hatch/door and the pellet lid.
Once 60 seconds have passed, during ignition the stove will go into "DEPR ALARM" mode, while during normal operation
the stove will go into "COOLING STAND BY" mode before automatically resuming operation once the conditions are
satised (cold stove, etc.).
aiR Zone conTRol This message, visible in the WORK phase, indicates that the appliance is optimising the distribution of hot air between
the installation room and the ducted room.
alaRMs
Display eXplanaTion soluTion
Indicates the presence of an alarm.
On: indicates the presence of an alarm
The alarm can only be reset if the fumes motor has stopped and 15
minutes have passed since the alarm was displayed, by pressing key 6
for 3 seconds.
fuMes MoToR
faulT Fumes motor fault Contact after-sales centre
fuMes pRobe Fumes probe fault. Contact after-sales centre
HoT fuMes High fumes temperature Check pellet feed (see EASY SETUP”), if the problem cannot be solved,
contact a qualied technician.
no
iGniTion
The pellet hopper is empty.
Pellet feed calibration inadequate.
Thermostat bulbs tripped.
Check for the presence of pellets in the hopper.
Adjust the pellet ow (see EASY SETUP”).
Check the procedures described in the "IGNITION" chapter.
Check bulb thermostats (see chapter on Resetting)
no flaMe
The pellet hopper is empty.
No pellet feed.
The gearmotor does not feed pellets.
Check for the presence of pellets in the hopper.
Adjust the pellet ow (see EASY SETUP”).
DepR alaRM
The door is not closed correctly.
The ash drawer is not closed correctly.
The combustion chamber is dirty.
The fumes exhaust pipe is blocked/dirty
The vacuum detection channel inside the ash
drawers is clogged.
Check hermetic door closure.
Check hermetic closure of the ash drawer.
Check cleanliness of the fumes pipe and the combustion chamber.
Check and clean the hose connection and the ash drawer pressure
switch tube.
no
iGniTion - black ouT
No power during the ignition
phase.
Turn the stove off using key 6 and repeat the procedure
described in the "IGNITION" chapter.
Other reset operations should be performed by
an authorised technician.
coMManD auGeR
alaRM Abnormal pellet loading. Contact after-sales centre
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Extraflame Sharon Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Extraflame Sharon Plus in the language / languages: English as an attachment in your email.

The manual is 7.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Extraflame Sharon Plus

Extraflame Sharon Plus User Manual - German - 40 pages

Extraflame Sharon Plus User Manual - Dutch - 40 pages

Extraflame Sharon Plus User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info