695969
34
Zoom out
Zoom in
Previous page
1/40
Next page
34 ENGLISH
TO FIND OUT WHERE YOUR NEAREST SERVICE CENTRE IS, CONTACT YOUR DEALER OR GO TO THE WEBSITE WWW.LANORDICA-EXTRAFLAME.COM
Displays
Display
Reason
off
Generator
o
sTaRT
The start-up phase is in progress
pelleT loaDinG
Continuous pellet loading is in progress during the ignition phase
iGniTion
The ignition phase is in progress
pRepaRaTion
The preparation phase is in progress.
WoRk
The normal work phase is in progress.
MoDulaTion
The
generator
is working at minimum.
BloW
The automatic blow is active.
BuRn poT
CleaninG
The routine cleaning of the burn pot is in progress.
final CleaninG
The nal cleaning is in progress.
sTanD-By
Generator o waiting for re-ignition due to an external thermostat.
CoolinG
WaiTinG TiMe
The generator is required to turn on during the switch-o phase. If activated, the generator will turn on automatically as soon as
the safety conditions allow it.
H-off
Generator o due to water temperature over set.
T-off
Generator o waiting for re-ignition due to all requests met
WaiTinG
BlaCk ouT
The generator
is cooling after a power cut.
Once cooling is completed, it will re-start automatically
anTi-fReezinG
The anti-freezing function is in progress as the H2O temperature is below the factory set threshold
the pump is active until the water reaches the pre-set factory parameter +2°C
anTi-BloCk
The pump anti-block function is in progress (only if the generator has been in an OFF state for at least 96 hours); the pump is
activated for the time pre-set by the manufacturer, in order to prevent it from blocking
*eXCHanGeR
BloCkeD
The movement of the exchangers is blocked.
Switch o the machine and clean the exchangers. If the problem persists, contact the after-sales centre.
asH kiT CHeCk
The ash extractor is blocked.
Switch o the machine and empty out the ash drawer.
If the problem persists, contact the after-sales centre.
alaRMs
Display
eXplanaTion soluTion
Indicates the presence of an alarm.
On: indicates the presence of an alarm
Flashing: indicates the deactivation of the depression sensor.
The alarm can be reset only if the fumes motor has stopped and 15 minutes
have passed since the alarm was displayed, by pressing the key 1/
for 3
seconds.
fuMes MoToR
faulT
Fumes motor fault Contact after-sales centre
fuMes pRoBe
Fumes probe fault. Contact after-sales centre
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Extraflame PR20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Extraflame PR20 in the language / languages: English as an attachment in your email.

The manual is 4,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Extraflame PR20

Extraflame PR20 User Manual - German - 40 pages

Extraflame PR20 User Manual - Dutch - 40 pages

Extraflame PR20 User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info