695969
23
Zoom out
Zoom in
Previous page
1/40
Next page
23ENGLISH
STANDBY  ADDITIONAL THERMOSTAT
N.B. : INSTALLATION MUST BE PERFORMED BY AN AUTHORISED TECHNICIAN
It is possible to control the temperature of a room adjacent to the room where the stove is positioned; simply connect a thermostat following
the procedure described in the following section (it is advisable to place the optional mechanical thermostat at a height o the ground
equal to 1.50 m). Stove operation with the external thermostat connected in the clamp TA can be dierent depending on the activation or
deactivation of the STANDBY function.
By factory default, the clamp TA is jumpered, therefore it always has closed contact (on request).
ADDITIONAL THERMOSTAT FUNCTIONING WITH
STANDBY
ACTIVE
When the STANDBY function is active, the STBY icon will be on. When the contact or external thermostat is not satised (open contact /
temperature reached), the stove will switch o. As soon as the contact or external thermostat switches to the "not satised" status (closed
contact / temperature to be reached) it will re-ignite.
NB: stove operation depends on the temperature of the water inside the stove and relative factory setting restrictions. If the stove is
in HOFF (water temperature reached), any additional contact or thermostat request will be ignored.
ADDITIONAL THERMOSTAT OPERATION WITH
STANDBY
DEACTIVATED
When the STANDBY function is not active, the STBY icon will be o.
When the contact or external thermostat is satised (open contact / temperature reached), the stove will go to minimum. As soon as the
contact or external thermostat switches to the "not satised" status (closed contact / temperature to be reached) the stove will start to work
again at the pre-set power.
NB: stove operation depends on the temperature of the water inside the stove and relative factory setting restrictions. If the stove is
in HOFF (water temperature reached), any additional contact or thermostat request will be ignored.
ADDITIONAL THERMOSTAT INSTALLATION
Switch the appliance o using the master switch positioned on the rear of the stove.
Remove the plug from the socket.
Refer to the wiring diagram and connect the two thermostat wires in the relevant terminals located on the back of the stove, one
red and one black (clamp TA). In each model, the position or colour of the terminals may be dierent. The picture is for illustrative
purposes only.
J
TO ACTIVATE STAND-BY, REFER TO THE SETTINGS CHAPTER
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Extraflame PR20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Extraflame PR20 in the language / languages: English as an attachment in your email.

The manual is 4,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Extraflame PR20

Extraflame PR20 User Manual - German - 40 pages

Extraflame PR20 User Manual - Dutch - 40 pages

Extraflame PR20 User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info