695853
31
Zoom out
Zoom in
Previous page
1/36
Next page
31ENGLISH
Displays
Display Reason
off
Generator o
sTaRT
The START phase is in progress
pelleT loaDinG
Continuous pellet loading is in progress during the ignition phase
on
The ignition phase is in progress
pRepaRaTion
The preparation phase is in progress
WoRk
The normal work phase is in progress
MoDulaTion
The generator is operating at the minimum speed
final cleaninG
The nal cleaning is in progress
sTanD-by
Generator o waiting to turn back on due to the thermostat.
coolinG
sTanD by
A new ignition is attempted when the generator has just be switched o. When the generator is switched o, it is
necessary to wait for the fumes motor to switch o completely, then clean the burn pot. Only after performing these
operations will it be possible to switch the generator on again.
black ouT
sTanD by
The generator is cooling down after a power failure.
After the cooling phase, it will turn back on automatically
bloW
The automatic blow is active
CLOSE HOPPER -
STOVE DOOR
This indication means that you have 60 seconds to close the hatch/door and the pellet lid.
Once 60 seconds have passed, during ignition the stove will go into "DEPR ALARM" mode, while during normal
operation the stove will go into "COOLING STAND-BY" mode before automatically restarting when the conditions are
satised (cold stove, etc.).
alaRMs
Display eXplanaTion soluTion
Indicates the presence of an alarm.
On: indicates the presence of an alarm
The alarm can be reset only if the fumes motor has stopped and 15
minutes have passed since the alarm was displayed, by pressing key 1
for 3 seconds.
fuMes MoToR
faulT
Fumes motor failure Contact the service centre
fuMes pRobe
Fumes probe fault. Contact the service centre
HoT fuMes
High exhaust temperature
Check pellet loading (see "Easy setup"); if the problem is not solved,
contact a qualied technician.
no
iGniTion
The pellet hopper is empty.
Unsuitable pellet loading calibration.
Thermostat bulbs tripped.
Check for the presence of pellets in the hopper.
Adjust the pellet ow (see “Easy setup”).
Check the procedures described in the "Ignition" chapter.
Check the thermostats with bulbs (see chapter on Resetting)
no flaMe
The pellet hopper is empty.
Pellets not loading.
The gear motor is not loading pellets.
Check for the presence of pellets in the hopper.
Adjust the pellet ow (see “Easy setup”).
DepR alaRM
The door is not closed properly.
The ash drawer is not closed properly.
The combustion chamber is dirty.
The fumes exhaust pipe is blocked/dirty
Check that the door closes hermetically.
Check that the ash drawer closes hermetically.
Make sure that the fumes pipe and the combustion chamber are clean.
no
iGniTion - black ouT
No power during the ignition
phase.
Turn the stove off by pressing key 1 and repeat the procedures
described in the "Ignition" chapter.
Other restoration operations must be performed by
an authorised technician.
alaRM
coMManD auGeR
Abnormal operation of pellet loading. Contact the service centre
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Extraflame Lucia at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Extraflame Lucia in the language / languages: English as an attachment in your email.

The manual is 5,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Extraflame Lucia

Extraflame Lucia User Manual - German - 36 pages

Extraflame Lucia User Manual - Dutch - 36 pages

Extraflame Lucia User Manual - French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info