696235
15
Zoom out
Zoom in
Previous page
1/32
Next page
15ENGLISH
STANDBY
The STBY function is used if immediate stove switch-o is required when the set temperature has been
reached.
The STBY function can be set at ON or OFF using the procedure described further on.
In the factory the STBY function is always set at OFF (indicator o)
STBY FUNCTION SET AT ON
If the STBY function is active (ON), when the stove reaches the set room temperature and exceeds it by 2°C, it will switch o after a default
delay time, displaying STAND  BY.
When the room temperature is 2°C lower than the setting, the stove will start to work again at the power set on the display, displaying
WORK.
STBY FUNCTION SET AT OFF DEFAULT SETTING
If the stby function is not active (OFF), if the stove reaches the set room temperature, it will go to minimum, modulating and displaying
MODULATION. When the room temperature is below the setting, it will start to work again at the set power, displaying WORK.
CONTROLS PROCEDURE
press key 5 for a few seconds, until SET CLOCK appears.
Press key 3 until "USER" appears.
Press key 5 twice.
Use key 2 or 3 "ON" to activate or "OFF" to de-activaate.
Press key 1 several times to conrm and exit the menu.
N.B.: If these calibrations do not solve the problem, please contact your local customer service centre.
CONTROL PROCEDURE
Press the key 5 for a few seconds; the message SET CLOCK will appear on display.
Press the key 3 for several times to open the EASY SETUP page.
Press the key 5 to conrm.
Use the keys 2 and 3 to increase (3) or decrease (2) the value.
Press the key 1 for several times to conrm and exit the menu.
EASY SETUP
The volumetric weight of the pellet is the ratio between the weight and the volume of the pellet. This ratio can change while maintaining
the quality of the pellet. By using the EASY SETUP function, it is possible to change the calibration of the volumetric weight, increasing or
decreasing the pre-set values.
In the stove program, the values available go from “– 3”to “+ 3”; all the stoves are calibrated at the factory to the optimal value 0
If you notice an excessive deposit on the burner pot, enter the EASY SETUP program and lower the value by one unit to “- 1”; then wait for the
following day and if there is no improvement, lower the value again up to a maximum of “- 3”. Instead, should it be necessary to increase the
calibration of the volumetric weight of the pellet, it is advisable to go from the default value “0” to “+ 1, + 2, + 3” as required.
EXCESSIVE DEPOSIT OF PELLETS IN THE BURNING
POT
NORMAL OPERATION LITTLE DEPOSIT OF PELLETS IN THE BURNING POT
-3 -2 -1 0 +1 +2 +3
THIRD
DECREASING
RANGE IF THE
FIRST TWO ARE
NOT ENOUGH
SECOND
DECREASING
RANGE IF THE
FIRST IS NOT
ENOUGH
FIRST
DECREASING
RANGE (TEST FOR
1 DAY )
OPTIMAL DEFAULT
VALUE
FIRST
INCREASING
RANGE
SECOND
INCREASING
RANGE IF THE
FIRST IS NOT
ENOUGH
THIRD
INCREASING
RANGE IF THE
FIRST TWO ARE
NOT ENOUGH
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Extraflame Ketty Evo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Extraflame Ketty Evo in the language / languages: English as an attachment in your email.

The manual is 4,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Extraflame Ketty Evo

Extraflame Ketty Evo User Manual - German - 32 pages

Extraflame Ketty Evo User Manual - Dutch - 32 pages

Extraflame Ketty Evo User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info