811757
36
Zoom out
Zoom in
Previous page
1/40
Next page
36 ENGLISH
* if there is an additional system data sheet ** on models with this function.
alaRMs
Display eXplanaTion solUTion
Indicates the presence of an alarm.
On: indicates the presence of an alarm
Flashing: indicates the deactivation of the depression sensor.
The alarm can be reset only if the fumes motor has stopped and 15 minutes
have passed since the alarm was displayed, by pressing the key 1/ON/
for 3 seconds.
FUMes MoToR
FaUlT Fumes motor fault Contact after-sales centre
FUMes pRoBe Fumes probe fault. Contact after-sales centre
HoT FUMes High fumes temperature Check pellet feed (see “Pellet feed adjustment”). If the problem cannot be
solved, contact an authorised technician.
**CHaMB pRoBe Chamber probe fault. Contact the after-sales centre.
no
iGniTion
The pellet hopper is empty.
Pellet feed calibration inadequate.
Thermostat bulbs tripped.
Check for the presence of pellets in the hopper.
Adjust the pellet ow (see “Pellet load adjustment”).
Check the procedures described in the “Ignition” chapter.
Check bulb thermostats (see chapter on Resetting)
no
iGniTion
BlaCK oUT
No power during the ignition
phase.
Turn the stove o using key 1 and repeat the procedure
described in the "IGNITION" chapter.
Other reset operations should be performed by
an authorised technician.
no FlaMe
The pellet hopper is empty.
No pellet feed.
The gearmotor does not feed pellets.
Check for the presence of pellets in the hopper.
Check bulb thermostats (see chapter on Resetting)
Adjust the pellet ow (see “Pellet feed adjustment”).
DepR alaRM
The door is not closed correctly.
The ash drawer is not closed correctly (if
present)
Check hermetic door closure.
Check hermetic closure of the ash drawer (if present).
**Min DelTa-p
alaRM 1
The combustion chamber is dirty.
The fumes exhaust pipe is blocked/dirty
The vacuum detection channel inside the ash
drawers is clogged.
Check cleanliness of the fumes pipe and the combustion chamber.
Check and clean the hose connection and the ash drawer pressure switch
tube.
Contact after-sales centre
H2o pRoBe H2O probe fault Contact after-sales centre
Min H2o pRessURe
alaRM
The system pressure read by the pressure switch
is too low.
Possible air in the system; bleed the system. Possible lack of water or leaks
due to anomalies in some system component.
If the problem persists, contact the service centre.
MaX H2o pRessURe
alaRM
The pressure of the water has exceeded the max
threshold
Possible air in the system; bleed the system. Check that the expansion
vessels are not damaged or under-dimensioned Check that the cold system
is loaded at the correct pressure
If the problem persists, contact the service centre.
aUGeR ConTRol
alaRM Abnormal pellet feeding. Contact after-sales centre
**aUGeR BloCKeD Abnormal operation of pellet motor. Contact after-sales centre
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Extraflame Isidora Idro H20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Extraflame Isidora Idro H20 in the language / languages: English as an attachment in your email.

The manual is 7.51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Extraflame Isidora Idro H20

Extraflame Isidora Idro H20 User Manual - German - 40 pages

Extraflame Isidora Idro H20 User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info