696314
32
Zoom out
Zoom in
Previous page
1/36
Next page
32 ENGLISH
fUMES PROBE
Fumes probe fault. Contact customer service
HOT EXHAUST
High fume temperature
Check the pellet loading (see “Easy Setup”); if the problem persists, contact a
qualied technician
ALL CLEAN CHECK UP
The door is not closed properly.
The ash drawer is not closed properly.
The combustion chamber is dirty.
The fume exhaust duct is blocked.
Check the hermetic closure of the door.
Check the hermetic closure of the ash drawer.
Make sure that the fumes duct, the primary air duct sensor and the combustion
chamber are clean.
NO IGNITION
The pellet hopper is empty.
Pellet loading value inappropriate.
Thermostatic bulbs tripped.
Check for the presence of pellets inside the hopper.
Adjust the pellet ow (see “Easy Setup”).
Check the procedures described in the chapter “Ignition.
Check the bulb thermostats (see the chapter “Reset”)
BLACK OUT
NO IGNITION
No power during the ignition phase
Turn the stove OFF by pressing key 1 and repeat the procedures described in the
chapter “Ignition.
NO PELLET
The pellet hopper is empty.
Pellet not loading.
The gearbox is not loading pellets.
Check for the presence of pellets inside the hopper.
Adjust the pellet ow (see “Easy Setup”).
DEPRESSION ALARM
The door is not closed properly.
The ash drawer is not closed properly.
The combustion chamber is dirty.
The fume exhaust duct is blocked/dirty.
Check the hermetic closure of the door.
Check the hermetic closure of the ash drawer.
Make sure that the fumes duct and the combustion chamber are clean.
DAMAGE DEPR SENSOR
Flow sensor faulty.
Sensor disconnected
Contact customer service
WATER OVERTEMP
Air in the system
Circulation inappropriate
Possible air in the system, bleed the system.
No suitable circulation,.
No safety area or not suitable.
The water inside the stove is above 95°C.
Possible pump fault.
If the problem persists, the reset operations must be performed by an authorised
technician.
* TRAPDOOR BLOCKED
The automatic cleaning of the burning pot is
blocked.
Burning pot dirty/blocked
The door is not closed properly.
Check that the door is closed properly.
Check that the burning pot is free and clean.
The automatic cleaning of the burning pot is blocked.
If the problem persists, contact customer service
MIN H2O PRESSURE
ALARM
The system pressure detected by the pressure
switch is too low.
Possible air in the system, bleed the system.
Possible lack of water or leaks due to faults in some components of the system.
If the problem persists, contact customer service
PROBE H2O
H2O probe fault Contact customer service
MAX H2O PRESSURE
ALARM
The water pressure is above the maximum
threshold
Possible air in the system, bleed the system.
Make sure that the expansion vessels are not damaged or too small
Make sure that the system (cold) is loaded at the right pressure
If the problem persists, contact customer service
* PRESSURE SENSOR
DAMAGED
Pressure dierential sensor faulty, disconnected or
broken
Contact customer service
* AUGER CONTROL
ALARM
Pellet loading not working correctly Contact customer service
* AUGER BLOCKED
Pellet motor not working correctly Contact customer service
* DHW PROBE
Boiler probe fault. Contact customer service
* PUffER TANK PROBE
Boiler probe fault. Contact customer service
* EMPTY HOPPER
The pellet hopper is empty.
The door is not closed properly.
The ash drawer is not closed properly.
The combustion chamber is dirty.
The fume exhaust duct is blocked..
Check for the presence of pellets inside the hopper.
Check the hermetic closure of the door.
Check the hermetic closure of the ash drawer.
Make sure that the fumes duct, the primary air duct sensor and the combustion
chamber are clean.
Contact customer service
* where available.
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Extraflame HP22 EVO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Extraflame HP22 EVO in the language / languages: English as an attachment in your email.

The manual is 3,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Extraflame HP22 EVO

Extraflame HP22 EVO User Manual - German - 36 pages

Extraflame HP22 EVO User Manual - Dutch - 36 pages

Extraflame HP22 EVO User Manual - French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info