643370
17
Zoom out
Zoom in
Previous page
1/36
Next page
17ENGLISH
FUNCTIONING AND LOGIC
IGNITION
Once the points listed previously have been checked, press key 1 for three seconds to ignite the stove. 15 minutes are given for the ignition
stage, after ignition and once the control temperature has been reached,
the stove interrupts the ignition phase and switches to the STARTING mode.
STARTING
During the start-up stage, the stove stabilises combustion, increasing it gradually, to then start ventilation and switch to the WORK mode.
WORK
During the work stage, the stove reaches the set power and works to reach the set room temperature. See following item
SET THERMOSTAT ADJUSTMENT
The room temperature setting can be set using buttons 2 and 3, from low-07 to 40°C -hot
LOW  HOT
if the temperature setting is on low” (set below the 7°C threshold) the stove will always function at minimum.
If the setting is on “hot (set above the 40°C threshold) the stove will not modulate, always functioning and only at the set power.
SET POWER ADJUSTMENT
Set the functioning power from 1 to 5 (settable using keys 4 - 5).
Power 1 = minimum level - Power 5 = maximum level.
WORK WITH ROOM PROBE STANDARD
The appliance controls the room temperature via a probe tted on the appliance.
Once the the set temperature has been reached, it will automatically go to minimum or switch o activating the Stand by function, reducing
pellet consumption to a minimum.
By default the STBY function is always set on OFF (light
on).
For its activation and logic, follow the indications on the next page, Chapter: Stand by.
BURN POT CLEANING
During the work stage, the stove has an internal counter which cleans the burn pot after a set amount of time.
This stage will be shown on the display, it will bring the stove to a lower power level and will increase the fumes motor for a programmed
amount of time.
when the cleaning stage is nished, the stove will continue its work, going back to the selected power level.
SWITCHOFF
Press key 1 for three seconds.
when the operation has been performed, the appliance automatically enters the switch- o phase, blocking the supply of pellets.
The fumes motor and the hot air ventilation motor will remain on until the temperature of the stove has dropped below the factory
parameters.
REIGNITION
The stove can only be re-ignited if the ue gas temperature has lowered and the preset timer has been reset to zero.
J
CLEAN CHECK UP 1  2
IF THE ALARM "CLEAN CHECK UP" ALARM IS PRESENT, IT IS NECESSARY TO MAKE
SURE THAT THE BOTTOM OF THE BURNING POT IS FREE FROM RESIDUES OR DIRT.
THE HOLES IN THE BOTTOM MUST BE COMPLETELY FREE, TO ENSURE CORRECT
COMBUSTION.
IT IS POSSIBLE TO USE THE "EASY SETUP" FUNCTION TO ADJUST THE COMBUSTION
DEPENDING ON THE REQUIREMENTS DESCRIBED. IF THE ALARM SIGNAL PERSISTS,
AND THE ABOVE MENTIONED CONDITIONS HAVE BEEN CHECKED, CONTACT
CUSTOMER SERVICE.
BOTTOM OF BURNING POT
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Extraflame Giusy at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Extraflame Giusy in the language / languages: English as an attachment in your email.

The manual is 6,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Extraflame Giusy

Extraflame Giusy User Manual - German - 28 pages

Extraflame Giusy User Manual - Dutch - 28 pages

Extraflame Giusy User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info