643371
15
Zoom out
Zoom in
Previous page
1/36
Next page
1
2
3
4
5
15ENGLISH
REMOTE CONTROL OPTIONAL
The heating power, the desired room temperature and the appliance ignition/switch o, can be adjusted using the remote control.
To ignite the stove, press key 1 for a few seconds; the appliance will automatically enter the ignition phase. It is possible to adjust power by
using keys 4 and 5, whereas the desired temperature can be adjusted using keys 2 and 3. To switch the stove o, press and hold key 1 for a
few seconds.
TYPE AND REPLACEMENT OF BATTERIES
The batteries are housed in the lower part of the remote control.
To replace it remove the battery-holder (as shown in the gure
on the back of the remote control), remove or insert the battery
following the symbols on the remote control and on the battery.
For operation, 1 CR2025, 3V lithium buer battery is required.
If the remote control is o because it has no
batteries, the stove can be controlled from the
control panel on top of it.
While replacing the battery, pay attention to the
polarity by observing the symbol on the inside
compartment of the remote control.
COMMISSIONING SETTINGS
Once the power cable at the back of the stove has been connected, move the switch, also located on the back, to (I).
The switch at the back of the stove powers the stove board.
The stove remains o and a rst screen appears on the panel
reading OFF.
MAINS FREQUENCY 50/ 60HZ
In the event the stove is installed in a country with 60Hz frequency, the stove will display "frequenza rete errata" ("mains frequency incorrect").
Vary the frequency as described below.
CONTROLS PROCEDURE
Press key 5.
Select 50 - 60Hz frequency with key 2 -3.
Conrm using key 5 and exit the menu by pressing key 1.
THE BATTERIES USED CONTAIN METALS HARMFUL FOR THE ENVIRONMENT. THEY MUST THEREFORE BE DISPOSED OF
SEPARATELY IN APPROPRIATE CONTAINERS.
15


Need help? Post your question in this forum.

Forumrules
1

Forum

extraflame-giusy-plus

Reset search

  • Hallo Zusammen,

    ich habe einen Extraflame Guisy .
    Im Display wird eine Fehlermeldung "Luftmengensensor ho" angezeigt.
    wie kann ich das beheben??
    In der Bedienungsanleitung finde ich keine Einstellung dazu.
    Submitted on 18-10-2021 at 08:36

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Extraflame Giusy Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Extraflame Giusy Plus in the language / languages: English as an attachment in your email.

The manual is 6,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Extraflame Giusy Plus

Extraflame Giusy Plus User Manual - German - 28 pages

Extraflame Giusy Plus User Manual - Dutch - 28 pages

Extraflame Giusy Plus User Manual - French - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info