811681
19
Zoom out
Zoom in
Previous page
1/40
Next page
1
23
45
6
1 4
3
2
5
6
19ENGLISH
GENERAL MENU Go back - exit
Scroll parameters: next (3); previous (2)
Change settings data: increase (4); decrease (5)
Conrm - access menu
J
MAKE SURE THAT THERE ARE NO RESIDUES OR DIRT AT THE BOTTOM OF
THE BURN POT. THE HOLES AT THE BOTTOM MUST BE COMPLETELY FREE
TO GUARANTEE PROPER COMBUSTION. THE "EASY SETUP" FUNCTION
CAN BE USED TO ADAPT COMBUSTION BASED ON THE DESCRIBED
NEEDS.
BURN POT BOTTOM
FRONT AIR SET
AIR DUCTING SET
EASY SETUP SET
CHRONO ENABLING
PRG1
PRG2
SETTINGS DATETIME PRG3
LANGUAGE PRG4
DISPLAY
STAND BY
DELTAT
FIRST LOAD
DEGREES
RESET
*TECHNICIANS ONLY
EASY CONTROL
*STOVE STATUS
*TECH
MENU
GENERAL WARNINGS
Advice to follow for the rst start-ups of the product:
During the rst hours of operation, there may be some smoke or
odours, but they are due to the normal “thermal break-in process.
During this process, the duration of which changes depending on
the product, it is recommended to:
Ventilate the room well
If present, remove any majolica or natural stone parts from the
top part of the product
Activate the product at the maximum power and temperature
Avoid remaining in the room for a long time
Do not touch the surfaces of the product
Notes:
The process is completed after a few heating/cooling cycles.
For combustion, do not use elements or substances other than those
indicated in the manual.
Before turning on the product, it is necessary to perform the
following checks:
If it is intended to be connected to a hydraulic system, it must
be complete and fully functional and in compliance with the
instructions given in the product manual and with the relevant
regulations in force.
The pellet hopper must be fully loaded
The combustion chamber and the burn pot must be clean
Make sure that the re holder, the ash drawer and the pellet
hopper close hermetically (if present in the hermetic version); they
must be closed and there must be no foreign bodies in the sealing
elements and gaskets.
Check that the power cord is properly connected
The bipolar switch (if present) must be set to position “1”.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Extraflame GABRIELLA PLUS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Extraflame GABRIELLA PLUS in the language / languages: English as an attachment in your email.

The manual is 7.44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Extraflame GABRIELLA PLUS

Extraflame GABRIELLA PLUS User Manual - German - 40 pages

Extraflame GABRIELLA PLUS User Manual - Dutch - 40 pages

Extraflame GABRIELLA PLUS User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info