811726
17
Zoom out
Zoom in
Previous page
1/36
Next page
1
23
45
6
1 4
3
2
5
6
17ENGLISH
GENERAL MENU Go back - exit
Scroll parameters: next (3); previous (2)
Modify data settings: increase (4); decrease (5)
Conrm - access menu
J
MAKE SURE THAT THE BOTTOM OF THE BURN POT IS FREE FROM
RESIDUE AND DEPOSITS. THE HOLES AT THE BOTTOM MUST BE
COMPLETELY FREE TO GUARANTEE PROPER COMBUSTION. THE "EASY
SETUP" FUNCTION CAN BE USED TO ADAPT COMBUSTION BASED ON
THE DESCRIBED NEEDS.
BURN POT BASE
GENERAL WARNINGS
Advice to follow for the rst start-ups of the product:
During the rst hours of operation, there may be some smoke or
odours, but they are due to the normal “thermal break-in process.
During this process, the duration of which changes depending on
the product, it is recommended to:
Ventilate the room well
If present, remove any majolica or natural stone parts from the
top of the product
Activate the product at the maximum power and temperature
Avoid remaining in the room for a long time
Do not touch the surfaces of the product
Notes:
The process is completed after a few heating/cooling cycles.
Do not use for the combustion of elements or substances other than
those indicated in the manual.
Before turning on the product, it is necessary to perform the
following checks:
If it is intended to be connected to a hydraulic system, it must
be complete and fully functional and in compliance with the
instructions given in the product manual and with the relevant
regulations in force.
The pellet hopper must be completed loaded
The combustion chamber and the burn pot must be clean
Make sure that the re holder, the ash pan and the pellet
hopper close hermetically (if present in the hermetic version); they
must be closed and there must be no foreign bodies in the sealing
elements and gaskets.
Check that the power cord is properly connected
The switch (if present) must be set to position “1”.
FRONT AIR SET
* AIR DUCTING SET
**TEMPERATURE
***AIR ZONE CONTROL SET
EASY SETUP SET
CHRONO ENABLING
PRG1
PRG2
SETTINGS DATETIME PRG3
LANGUAGE PRG4
DISPLAY
STAND BY
*PLUS VERSION ONLY
** IF A TEMPERATURE PROBE IS CONNECTED
*** VISIBLE ONLY IF AIR DUCTING IS ENABLED FROM THE MENU
USER SET OTHER THAN OFF
**** TECHNICIANS ONLY
DELTAT
****STOVE STATUS FIRST LOAD
DEGREES
****TECH MENU RESET
EASY CONTROL
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Extraflame DAHIANA PLUS VFS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Extraflame DAHIANA PLUS VFS in the language / languages: English as an attachment in your email.

The manual is 11.02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Extraflame DAHIANA PLUS VFS

Extraflame DAHIANA PLUS VFS User Manual - German - 36 pages

Extraflame DAHIANA PLUS VFS User Manual - Dutch - 36 pages

Extraflame DAHIANA PLUS VFS User Manual - French - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info