564675
37
Zoom out
Zoom in
Previous page
1/39
Next page
Symptom Possible Cause Remedy
Appliance is not switched on. Switch on the appliance.
Mains plug is not plugged in or is
loose.
Insert mains plug.
Fuse has blown or is defective. Check fuse, replace if necessary.
Appliance does not work.
Socket is defective. Mains malfunctions are to be
corrected by an electrician.
Appliance cools too much. Temperature is set too cold. Turn the temperature regulator
to a warmer setting temporarily.
Temperature is not properly adjusted. Please look in the “initial Start
Up” section.
Door was open for an extended
period.
Open the door only as long as
necessary.
A large quantity of warm food was
placed in the appliance within the last
24 hours.
Turn the temperature regulation
to a colder setting temporarily.
The food is too warm.
The appliance is near a heat source. Please look in the “installation
location” section.
Interior lighting does not work. Light bulb is defective. Please look in the “changing the
Light Bulb “section.
Heavy build-up of frost,
possibly also on the door seal.
Door seal is not air-tight(possibly
after reversing the door).
Carefully warm the leaking
sections of the door seal with a
hair dryer(on a cool setting). At
the same time shape the
warmed door seal by hand such
that it sits correctly.
Appliance is not level. Readjust the feet.
The appliance is touching the wall or
other objects.
Move the appliance slightly.
Unusual noises.
A component, e.g. a pipe, on the rear
of the appliance is touching another
part of the appliance or the wall.
If necessary, carefully bend the
component out of the way.
The compressor does not start
immediately after changing the
temperature setting.
This is normal, no error has occurred. The compressor starts after a
period of time.
Water on the floor or storage
shelves.
Water drain hole is blocked. See the “cleaning and care”
section.
Changing the light bulb
Warning!
If the LED light bulb is damaged, DO NOT CHANG IT BY THE USER!
Changing the LED light bulb carry out by inexperienced persons may cause injury or serious
malfunctioning.
it must be replaced by a qualified persons in order to avoid a hazard. Contact your local Service
Force Center for help.
Before changing the light bulb, switch off the appliance and unplug it, or pull the fuse or the
circuit breaker.
LED light bulb data: 220-240 V,
To switch off the appliance, set the temperature regulator to position Ā0ā.
KGC 250/70-1 A+++ Version E1.0 EN 01/2014 Page 13 of 15
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Exquisit KGC 250-70-1 A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Exquisit KGC 250-70-1 A in the language / languages: Dutch as an attachment in your email.

The manual is 3,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info