Manual EWT Nyman (page 4 of 24) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

460327

Zoom out

Zoom in

1/24

- 1 -

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

General

Unpack the heater carefully and retain the packaging for possible future use, in the

event of moving or returning the fire to your supplier.

The fire incorporates a flame effect, which can be used with or without heating, so that

the comforting effect may be enjoyed at any time of the year. Using the flame effect on

its own only requires little electricity.

These models are designed to be free standing and are normally positioned against a

wall.

Before connecting the heater check that the supply voltage is the same as that stated

on the heater.

Please note: Used in an environment where background noise is very low, it may

be possible to hear a sound which is related to the operation of the flame effect.

This is normal and should not be a cause for concern.

Electrical connection

WARNING – THIS APPLIANCE MUST BE EARTHED

This heater must be used on an AC ~ supply only and the voltage marked on the

heater must correspond to the supply voltage.

Before switching on, please read the safety warnings and operating instructions.

Controls - see Fig. 2

Three switches provide a choice of heat settings. A switch is in the ON position when

the side with the markings on (i.e. I, I, or II) is pushed in.

Thermal Safety Cut-out

A thermal safety cut-out is incorporated in the heater to prevent damage due to

overheating. This can happen if the heat outlet was restricted in any way. The heater

will switch on once the obstruction has been removed and the heater has cooled. If the

cut-out continues to operate intermittently, the heater should be switched off and a

service agent contacted.

Maintenance

WARNING: ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE

ATTEMPTING ANY MAINTENANCE.

Lamp Replacement - see Fig. 3, Fig. 4 and Fig. 5

The lamps are located behind the back panel. To gain access to the lamps, the screws

indicated in Fig. 3 which secure the back panel, must be removed.

Remove and slide out panel as indicated on Fig. 4.

Remove the defective lamp by unscrewing it as shown in Fig .5.

Replace with a 60W E14 SES Clear candle lamp. Take care not to over-tighten the

lamp.

Refit the back panel and secure with the screws.

Cleaning

WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE

CLEANING THE HEATER.

For general cleaning use a soft clean duster – never use abrasive cleaners. The glass

viewing screen should be cleaned carefully with a soft cloth. DO NOT use proprietary

glass cleaners.

To remove any accumulation of dust or fluff the soft brush attachment of a vacuum

cleaner should occasionally be used to clean the outlet grille of the fan heater.

Recycling

For electrical products sold within the European Community.

At the end of the electrical products useful life it should not be disposed of with

household waste. Please recycle where facilities exist. Check with your Local

Authority or retailer for recycling advice in your country.

After Sales Service

Should you require after sales service or should you need to purchase any spares,

please contact the retailer from whom the appliance was purchased or contact the

service number relevant to your country on the warranty card. Please do not return a

faulty product to us in the first instance as this may result in loss or damage and delay

in providing you with a satisfactory service. Please retain your receipt as proof of

purchase.

Important Safety Advice:

When using electrical appliances, basic precautions should always be

followed to reduce the risk of fire, electrical shock and injury to persons,

including the following:

If the appliance is damaged, check with the supplier before installation and

operation.

Do not use outdoors.

Do not use in the immediate surroundings of a bath, shower or swimming

pool.

Do not locate the heater immediately below a fixed socket outlet or

connection box.

This appliance is not intended for use by children or other persons without

assistance or supervision if their physical, sensory or mental capabilities

prevent them from using it safely. Children should be supervised to ensure

that they do not play with the appliance.

Do not use this heater in series with a thermal control, a program controller,

a timer or any other device that switches on the heat automatically, since a

fire risk exists when the heater is accidentally covered or displaced.

Ensure that furniture, curtains or other combustible material are positioned

no closer than 1 metre from the heater.

In the event of a fault unplug the heater.

Unplug the heater when not required for long periods.

Although this heater complies with safety standards, we do not recommend

its use on deep pile carpets or on long hair type of rugs.

The appliance must be positioned so that the plug is accessible.

If the supply cord is damaged it must be replaced by the manufacturer or

service agent or a similarly qualified person in order to avoid a hazard.

Keep the supply cord away from the front of the heater.

WARNING: In order to avoid overheating, do not cover the heater. Do

not place material or garments on the heater, or obstruct the air

circulation around the heater. The heater carries the Warning symbol

indicating that it must not be covered.

Switch 1 (I) Controls the electricity supply to the heater and flame effect.

Note: This switch must be in the ON (I) position for heater to

operate with or without heat.

Switch 2 (I) Provides 1kW heat output

Switch 3 (II) Provides 2kW output with switch 2

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of EWT Nyman in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,08 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

EWT Nyman Manual

Product: