814565
51
Zoom out
Zoom in
Previous page
1/78
Next page
Brief introduction
Reversing the door
The side at which the door opens can be
changed from the right side (as supplied) to the
left side, if the installation site requires.
Tools you will need:
1. 8mm socket driver
2. Cross-shaped screwdriver
3. Putty knife or thin-blade screwdriver
Before you start lay the refrigerator on it’s back in
order to gain access to the base, you should rest
it on soft foam packaging or similar material to
avoid damaging the cooling pipes at the rear of
the refrigerator.
6 Screw Bolt
7 Upper Hinge Cap
8
Shaft Sleeve
9 Plug
1 Screw
2 Low Hinge
3 Adjustable Low Foot
4 Adjustable High Foot
5 Upper Hinge
Refrigerator without cover panel
Refrigerator with cover panel
Screw
Cover panel
1. Open the appliance door and unhinge and remove all
fittings from inside the appliance.
2. Unscrew the 2 screws (10). (Refrigerator with cover
panel)
3.
Take off the cover panel (11) and set it down on a soft
surface. (Refrigerator with cover panel)
4. Remove the upper hinge cap (7). (Refrigerator without
cover panel)
5. Remove the two screws blot (6) that connect the upper
hinge (5) on the right side of the cabinet top.
6. Carefully lift the door and place it on a padded surface
to prevent scratching.
7. Remove the plug (9) and transfer it to the uncovered
hole on the right side of the unit. Be sure to press the
button firmly into the hole. (Refrigerator without cover
panel)
8. Remove the two screws (1) that hold the lower hinge (2)
on the right side of the unit.
9. Remove the screw-type leveling front leg (4) and
transfer it to the right side as shown in the adjacent figure.
10. Set the door into it’s new place making sure the pin
enters the bushing at the lower frame section (hole).
11. Secure the upper hinge (5) previously removed in step
6 on the left side of the unit. Make sure the pin enters the
bushing on the upper frame section (hole).
12. Loosely secure the lower left hinge (2) and do not
tighten the bolts until the door is in the closed position
and leveled.
13. lnsert the plug (9) on the uncovered holes (right side).
(Refrigerator without cover panel)
14. Replace the upper hinge cap (7). (Refrigerator without
cover panel)
15. Turn the appliance upright again.
16. Mount the cover panel (11) at the front and lay it flat on
the rear. (Refrigerator with cover panel)
17. Apply the 2 screws (10) and tighten. (Refrigerator with
cover panel)
18. Open the appliance doors and attach all fittings.
13
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Everglades EVCO1021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Everglades EVCO1021 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info