751942
29
Zoom out
Zoom in
Previous page
1/39
Next page
28
04. PRODUCT USE
Alarms
In the event that an operating anomaly occurs, the board intervenes and signals the occurrence of an irregularity, turning on the alarm LED
(alarm LED on) and emitting acoustic signals.
The possible alarm messages are listed below:
Display shows No. Cause
ALARM BLACK-OUT (1) Absence of mains voltage
ALARM FUME TEMP. (2) Fume overheating
ALARM REG. ENCODER (3) Check encoder
ALARM NO ENCODER (4) Fume fan fault, not working
ALARM IGNITION UNSUCCESSFUL (5) Stove does not ignite
ALARM CHECK PELLETS (6) Shutting down due to insufficient pellets
ALARM THERMAL SAFETY (7) Safety thermostat activated
ALARM NO DEPRESSION (8) Depressor activated
ALARM AUGER TUBE SAFETY (10) The auger tube turns continuously
ALARM INSUFFICIENT DRAUGHT (11) Burn pot or air extraction pipe obstructed
ALARM CLEANER FAULT (12) The burn pot cleaner is blocked
ALARM AUGER TUBE ENCODER (13) The board does not read the auger tube encoder. No connection
ALARM AUGER TUBE TRIAC (14) The auger tube turns continuously
In case of alarm, the stove is always immediately switched off
EXCEPT FOR THE POWER OUTAGE ALARM, the alarm status is reached at the end of the period of a time set by and can be cleared by holding
P3 button down. Whenever an alarm is cleared, the stove starts a switching-off phase for safety reasons. The alarm LED (alarm LED on) will
remain on and the buzzer, if enabled, will sound intermittently during the entire alarm phase. Should the alarm not be cleared, the stove will in
any case be switched off and the alarm message will remain on the display.
Safety thermostat
If the general safety thermostat detects a water value exceeding the trigger threshold, it
immediately switches off the auger tube (to which it is connected in series), while acquiring this
change in status. The message THERMAL SAFETY ALARM appears on the display and the system is
switched off. Unscrew the black cap on the back of the stove and press the button to reset the
contact.
Negative Pressure Alarm
This alarm occurs if:
The vent pipe is non-compliant: the pipe must minimise the Pascals required by the manufacturer (see TECHNICAL DATA) at both low
and maximum power.
Vent pipe or combustion air outlet obstructed.
Combustion chamber door and/or pellet hopper door open.
Excessive dirt inside the fume fan: it is necessary to empty the ash that settles in the area adjacent to the ash drawer compartment.
Black-out Alarm
In the event that there is an electrical power failure for a given time, the stove, with restoring of the electricity, will change to BLACK-OUTalarm.
It is necessary to wait for the stove to cool down and then turn it back on.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eva Calor TRINITY at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eva Calor TRINITY in the language / languages: English as an attachment in your email.

The manual is 2,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info