668821
41
Zoom out
Zoom in
Previous page
1/47
Next page
06. TROUBLESHOOTING
40
PROBLEM
CAUSE
SOLUTION
FIRST START-UP
IT MAY BE NECESSARY TO REPEAT THE FIRST LOAD PHASE A FEW TIMES TO FACILITATE THE APPLIANCE FIRST START-UP
SINCE THE AUGER TUBE IS COMPLETELY EMPTY AND IT MAY TAKE A SPECIFIC PERIOD OF TIME TO FILL.
DISPLAY
SWITCHED OFF
POWER OUTAGE
CHECK PLUG AND POWER SUPPLY.
FAULTY ELECTRICAL CABLE
CALL TECHNICAL ASSISTANCE.
INTERRUPTED FUSE IN
CONTROL BOARD
CALL TECHNICAL ASSISTANCE.
FAULTY CONTROL BOARD
CALL TECHNICAL ASSISTANCE.
FAULTY DISPLAY
CALL TECHNICAL ASSISTANCE.
ALARM
NO FIRE
PELLETS NOT
FED TO
BURN POT
PELLETS
FALL BUT
NOT LIT
STOVE
SWITCHES
OFF DURING
NORMAL
FUNCTIONING
NO PELLETS
CHECK HOPPER
SAFETY THERMOSTAT
TRIGGERED
MANUALLY RESET THE THERMOSTAT LOCATED ON STOVE BACK.
AUGER TUBE BLOCKED BY
FOREIGN BODY
DISCONNECT PLUG, EMPTY HOPPER, REMOVE ANY FOREIGN BODY, SUCH AS NAILS, ETC.
FAULTY AUGER TUBE MOTOR
CALL TECHNICAL ASSISTANCE.
ACTIVE ALARM
SEE ALARM SECTION.
DIRTY BURN POT
CLEAN BURN POT.
TEMPERATURE TOO COLD
REPEAT SWITCHING-ON PHASE SEVERAL TIMES, EMPTYING THE BURN POT UPON EACH
TIME.
DAMP PELLETS
CHECK PELLET STORAGE LOCATION.
FAULTY IGNITION PLUG
CALL TECHNICAL ASSISTANCE.
FAULTY FUME SENSOR
CALL TECHNICAL ASSISTANCE.
FAULTY EXHAUST BLOWER
CALL TECHNICAL ASSISTANCE.
FAULTY CONTROL BOARD
CALL TECHNICAL ASSISTANCE.
POWER OUTAGE
CHECK PLUG AND POWER SUPPLY.
NO PELLETS
CHECK HOPPER
AUGER TUBE BLOCKED BY
FOREIGN BODY
DISCONNECT PLUG, EMPTY HOPPER, REMOVE ANY FOREIGN BODY, SUCH AS NAILS, ETC.
POOR QUALITY PELLETS
CHANGE PELLET TYPE.
INSUFFICIENT PELLET SET
VALUE AT MINIMUM HEAT
OUTPUT
CALL TECHNICAL ASSISTANCE.
ACTIVE ALARM
SEE ALARM SECTION.
POOR FLAME
ANTI-EXPLOSION DEVICE PLUG MISSING OR NOT CORRECTLY POSITIONED.
PARTIALLY CLOGGED VENT PIPE
CLEAN VENT PIPE IMMEDIATELY.
COMBUSTION AIR NOT
SUFFICIENT
CLOGGED AIR INTAKE.
CLOGGED STOVE
CLEAN BURN POT AND ASH DRAWER.
FAULTY / DIRTY EXHAUST
BLOWER
GET IT CLEANED BY A SPECIALISED TECHNICIAN CALL TECHNICAL ASSISTANCE
INADEQUATE COMBUSTION AIR
SET VALUE
CALL TECHNICAL ASSISTANCE.
ALARM NO RETE
POWER OUTAGE
SWITCH STOVE ON AND OFF, CHECK PLUG.
RiS / ECO
SET ROOM TEMPERATURE REACHED / STOVE WORKS PROPERLY
DISPLAY DOES
NOT WORK
SET ROOM TEMPERATURE
REACHED
INCREASE SET ROOM TEMPERATURE SO THAT APPLIANCE GOES BACK TO "WORKING"
MODE.
STOP FIRE
PERIODIC CYCLE OF BURN POT
CLEANING
STOVE WORKS PROPERLY
ALARM DEP
EXCESSIVE OR INADEQUATE
VENT PIPE LENGTH
NON-COMPLIANT VENT PIPE
CLOGGED OUTLET
CLEAN VENT PIPE / CALL AUTHORISED TECHNICIAN.
BAD WEATHER CONDITIONS
STRONG WIND.
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eva Calor Tosca 20 kW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eva Calor Tosca 20 kW in the language / languages: English as an attachment in your email.

The manual is 4,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eva Calor Tosca 20 kW

Eva Calor Tosca 20 kW User Manual - German - 38 pages

Eva Calor Tosca 20 kW User Manual - Dutch - 90 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info