668823
46
Zoom out
Zoom in
Previous page
1/55
Next page
- Cleaning and check of the tube and pressure gauge.
- Check and replacement, if necessary, of components that are subject to wear: brazier, resistance,
ash drawers, etc.
Additional instructions
Installation and assembly (Hydro pellet insert)
Installation
The product can be installed at any height, using the special adjustable frame (optional item), or
building props and non-flammable structures capable of supporting the weight of the product. The
Manufacturer rejects all responsibility for damage to people or property caused by the customer’s
failure to follow thee above instructions.
If you wish to install the pellet stove on a different structure or atop masonry works, proceed as
follows:
- Remove the two front lock-screws
- Remove the base from the pellet stove, sliding it until it comes off completely
- Place the base on the structure or masonry work you have prepared, leaving a space of 17 mm
from the front wall, and fasten the base using 5 wall plugs or screws.
- Before reassembling the pellet stove on the guides, make all the smoke exhaust, hydraulic and
electrical connections. Close the pellet stove making sure it slides all the way back; the position
sensor will not allow you to switch it on unless the installation has been performed properly. Refit
the lock-screws.
Connecting the smoke exhaust
Remember to factor in the presence of any flammable materials when drilling the hole for the
smoke exhaust pipe. If the hole has to cross a wooden wall or other heat-sensitive material, the
installer must use a wall connection and properly insulate the product feed-pipe using appropriate
insulating materials (thickness: 1.3-5 cm, with a minimum thermal conductivity of 0.07 W/m°K).
The same minimum distance is required even if the exhaust pipe is made to cross
vertical or horizontal segments that run close to the potentially flammable wall. For all information
concerning the possible case scenarios when installing the smoke exhaust, please refer
to the main manual.
Main air supply
During its operation, the product samples a certain amount of air for combustion from the
environment; this air must be integrated through an external air intake.
In this product, the combustion air intake is direct, so that you have to arrange grilles in the
surrounding structure. However, if you want to sample air externally, you will have to adjust the
pipe and connect it directly to the outside.
Electrical connection
Connect the cable included with the pellet stove to an electrical socket with ground connection.
Hood ventilation grilles
The product can be used in two different ways:
1. inserted into an existing cladding.
2. as a new installation.
If you choose to insert it into an existing cladding, you will have to use its ventilation grilles.
If, instead, you choose to use the product as a new installation, we recommend installing separate
ventilation grilles (convection air) with a size of at least 500 cm ², one for air exhaust into the
environment and one for
the intake, which can be installed either in position A or B.
The Manufacturer is not liable for possible damage to the structure or the electrical components
caused by failure to follow this instruction.
The structure reaches high temperatures and it is essential to ensure continuous and efficient
ventilation inside the cladding.
This will not only guarantee ideal operation, but will allow recovery of part
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eva Calor Tosca 15 kW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eva Calor Tosca 15 kW in the language / languages: English as an attachment in your email.

The manual is 5,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eva Calor Tosca 15 kW

Eva Calor Tosca 15 kW User Manual - German - 38 pages

Eva Calor Tosca 15 kW User Manual - Dutch - 90 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info