668823

Eva Calor Tosca 15 kW Manual

29
Zoom out
Zoom in
Previous page
1/55
Next page
- View water circuit pressure. Press and hold button 5.
Periodic brazier cleaning is also active during working mode. Brazier cleaning mode is activated
at regular intervals of about one hour. In this way, the smoke extractor works at maximum power
while pellet feeding is reduced to minimum. This operation is necessary for eliminating ash deposits
inside the brazier and for ensuring proper aeration and combustion. During brazier cleaning, the
display will show the message "BRAZIER CLEANING". If you notice excessive accumulation of
pellets in the brazier during normal operation, turn off the stove immediately and contact a
service centre. Forcing could make your stove a hazard.
6.3.4 Modulation based on room temperature (all models)
The stove is equipped with an internal temperature sensor that allows it to modulate its power
according to the desired room temperature.
For correct environment sensor operation, verify that the thermostat sensor positioned in the rear
of the stove under the outlet (see Figure 14) is away from the fume exhaust pipe and is not in
contact with objects or walls.
Press button "2" to set room temperature. The message " SET ROOM TEMP" will appear on the
bottom of the display, while the upper part will show the set temperature.
To modify this value, use buttons "1" and "2" until you reach desired temperature (7°C to 40°C).
If the room temperature reaches the set temperature, the stove goes into minimum power and
the last line of the display shows "MODULATE." This modulation has been completed only if the
room temperature returns to being lower than the set temperature. In this case, the stove will return
to the power set by the user and the display will show the message "MODULATE" and standard
working indications will return.
6.3.5 Modulation based on boiler water temperature (Hydro stoves and
boilers only)
The stove is equipped with boiler water temperature sensor that allows it to modulate its power
according to the desired temperature.
To set water temperature, press button "1". Press button "1" once and the bottom of the display
will show the message " SET WATER TEMP", while the upper part of the display will show the set
water temperature. To modify this value, use buttons "1" and "2" until you reach desired
temperature (30°C to 80°C). We recommend setting water temperature in the boiler between
60° C and 70° C.
Briefly press button "4" to exit from programming or wait a few seconds to automatically return to
the work or stand-by position.
During the working phase, if the water temperature in the boiler is much lower than the set value,
the stove operates at the maximum power level set.
However, when the boiler water temperature approaches the set value (difference of less than 3°
C), the stove heater gradually decrements the power level. The last line of the display shows a
flashing number that indicates the power level at which the stove is working at that moment. A
decrease in water temperature will correspond to an increase of the power level until it returns to
the maximum power value set initially. We recommend always setting Hydro stove power to its
maximum value "5".
If, despite reducing power, boiler water temperature continues to rise and reaches the set
temperature, the bottom line of the display will show "MODULATE." If, despite modulation, the
water temperature tends to rise further (for example when zone valves are closed), it may be best
to activate stand-by mode (see section 7.5).
6.3.6 Ventilation (air and channelled air models)
Air models provide ventilation which diffuses the heat generated from by the stove into the
surrounding environment. Activation of the ventilation occurs based on the temperature of fumes.
Therefore, it starts up after ignition and switches off with a delay compared to stove shutdown.
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eva Calor Tosca 15 kW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eva Calor Tosca 15 kW in the language / languages: English as an attachment in your email.

The manual is 5,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eva Calor Tosca 15 kW

Eva Calor Tosca 15 kW User Manual - German - 38 pages

Eva Calor Tosca 15 kW User Manual - Dutch - 90 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info