If you select the “STAND-BY” mode, the stove switches off after a period of time, set by Pr44, during which the room temperature remains at a value higher than
the SET temperature.
Only if the following condition occurs it is then possible to switch the stove back on:
TSET < (Tstove-Pr43)
FOR THE INSTALLER:
There are 3 standby modes:
Mode 1
WITH RESPECT TO THE WATER TEMPERATURE ENVIRONMENT PROBE
Having set the water temperature, commence operation of the stove.
1- With the room set reached, the stove goes into stand-by.
2- With the air set not reached, the stove is working.
Approaching the Water Set, the stove goes into modulation and remains in modulation.
It only goes into stand-by when the air set is reached.
It comes back on when the stove falls below the Air Set.
The room probe has priority.
In this case, the pump will shut off to maintain the temperature in the stove.
Mode 2
WITH RESPECT ONLY TO THE WATER TEMPERATURE
Having set the water temperature, commence operation of the stove.
Nearing the Set Water, the stove goes into modulation and when it is passed the Set goes into modulation and then stand-by.
Below Set the stove comes on again and resumes operation.
The stove in no way considers the temperature measured by the ambient sensor of the same stove.
Water takes priority.
Mode 3
WITH RESPECT TO THE THERMOSTAT AND TO THE TEMPERATURE OF THE WATER.
Having set the water temperature, commence operation of the stove.
1- With the thermostat open the stove goes into modulation and then stand-by.
2- With thermostat closed the stove is operational.
Nearing Set Water, the stove goes into modulation and remains in modulation. It only goes into stand by mode when the thermostat opens the contact. It turns
on when the thermostat closes the contact.
The stove in no way considers the temperature measured by the ambient sensor of the same stove.
The thermostat takes priority.
In this case, the pump will shut off to maintain the temperature in the stove
Menu 05 – BUZZER MODE
When "OFF", the acoustic signal is disabled.
Menu 06 – INITIAL LOAD
This function is important if the stove is new or if the stove is off due to the absence of pellets in the hopper.
INITIAL IGNITION MUST BE PERFORMED BY AUTHORISED PERSONNEL ONLY, NOT BY THE PURCHASER.
CONTACT THE ASSISTANCE CENTRE TO ARRANGE TO SEND OUT THE SPECIALIST TECHNICIAN TO YOU.
Use this function to load pellets for a pre-defined period when the stove is switched off and cold. Start with button P1 and stop with button P4. Initial loading is only
enabled if the stove is turned off.
Menu 07 – STOVE STATUS
This function displays the current status of the stove showing the status of all the devices connected to it. A few examples are included in the following pages. The
following will be displayed: status time (including ignition, shutdown, work, etc.), the pellet load and power, the flue gas temperature and the motor rpm, the board
temperature and the water pressure.
Menu 08 – TECHNICAL CALIBRATIONS
Menu for technicians, installers only.
13.3 USER FUNCTIONS
Standard functioning of a control board properly installed on a stove is described below with reference to the functions available to users. The indications listed
below refer to a control board fitted with programmable chrono-thermostat.
Stove ignition
Ensure that there are pellets in the hopper, that the burn pot is correctly positioned and free from any combustion residues and then close the door.
To turn on the stove, press button P4 for a few seconds. The display shows that the stove is on.
Start-up phase
The stove performs all the steps of the start-up phase according to the parameters concerning its levels and times. The display will show the wording ON, as there
is no pellet loading but the exhaust blower is in operation. PELLET LOADING state will occur where the pellets are being loaded into the burn pot. Once the pellets
have started to burn and the fume temperature is increased, the display will show FIRE ON, a transition phase between ignition and operating output.
Ignition fault
If the fume temperature has not reached the minimum permitted value after a predefined time, at a rate of 2°C/min, the stove goes into alarm status.
If there are unburned pellets inside the burn pot, it is necessary to empty the burn put before switching on the stove again. Pellet waste and potential bursting inside
the combustion chamber will thus be avoided. If the pellets have begun to burn but the alarm state persists, wait until all the pellets are burning and then switch on
again. Check that there are pellets inside the hopper.
Stove operational
At the end of the start-up phase, if no problems occurred, the stove enters its normal working mode.
If the temperature of the stove is the same as that set, the pump will come on, in this case at 55°C.
Upon reaching the set temperature of the stove, the stove will move into MODULATION and will work automatically at minimum power level.
Every 8 hours of continuous work, the stove performs automatic shutdown in order to guarantee cleaning of the burn pot and turbulators.
Changing set room temperature
To change the room temperature, simply press the P2 button. The display shows the current SET temperature value.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Eva Calor Sola at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Eva Calor Sola in the language / languages: English as an attachment in your email.
The manual is 4.77 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
