By using coaxial tubes, the air will be pre-warmed contributing to improved
combustion and lower emissions into the atmosphere.
Before installing, the following indications must be met:
Select the position where the stove is to be installed and:
•Arrangethe connection to the flue pipe for fume extraction.
•Arrange the external air intake (combustion air).
•Arrange the connection to the earthed mains.
•The electrical system of the room where the stove is to be installed must be
earthed, otherwise the control board may not work properly.
•Place the stove on the floor in a convenient position for the connection to the
flue pipe and close to the combustion air intake.
•The appliance must be installed on a floor with an adequate loading-bearing
capacity.
•Should the existing floor not comply with the requirement above, proper
measurements must be taken (for instance, the installation of a load distribution
plate).
•All items which could catch fire if exposed to excessive heat must be protected. Floors made from woodor inflammable materials must be protected using
non-combustible materials (e.g. 4mm-thick sheet metal or ceramic glass).
•Installation of the appliance must ensure easy access to clean the stove, exhaust ducts and flue pipe.
•This appliance is not suitableto be installed on a shared flue pipe.
•During normal operation, the stove draws air from the room where it is installed. An external air intake must therefore be positioned at the same height as the
pipe located on the rear of the stove. Exhaust fume pipes must be suitable for pellet stoves and therefore made from coated steel or stainless steel, with a
diameter of 8cm and fitted with adequate gaskets.
•The “air combustion” duct must reach an external wall or a wall of an adjacent room with external ventilation, as long it is not a bedroom or bathroom, nor at
risk of fire such as garages, storage rooms for combustible materials, etc. These air intakes must be created in such a way that they cannot be obstructed
either internally or externally and must be protected by a grille, wire mesh or other suitable guards provided that they do not reduce the minimum cross section.
•If the stove/boiler is to be installed in rooms where it is surrounded by combustible materials (e.g. furniture, wood cladding, etc.), the following minimum
clearances must be complied with:
STOVES
FLAMMABLE NONFLAMMABLE
REAR WALL P = 200mm
REAR WALL P = 150mm
SIDE WALL L = 400mm
SIDE WALL L = 200mm
FLOOR F = 0 mm
FLOOR F = 0 mm
FRONT R = 700mm
FRONT R = 700mm
It is, however, advisable, in addition to observing the minimum distances, to install the fireproof, heat-resistant insulating panels (rock wool, aerated concrete, etc.).
The following is recommend:
Promasil 1000
Classification temperature: 1000°C
Density: 245 kg/m3
Shrinkage at reference temperature, 12 h: 1.3/1000°C %
Cold crushing strength: 1.4 MPa
Bending strength: 0.5 MPa
Reversible thermal expansion: 5.4x10-6 m/mK
Specific heat capacity: 1.03 kJ/kg K
Thermal conductivity λ:
200 °C 0.07 W/mK
400 °C 0.10 W/mK
600 °C 0.14 W/mK
800 °C 0.17 W/mK
Thickness: 40 mm
•When the stove is on, it can create a depression in the room where it is installed, therefore there must not be any open flame apparatus in the same room,
with the exception of type C boilers (airtight).
•Make sure that the stove can draw the necessary quantity of combustion air: this must be from an open space (i.e. a space without exhaust blowers or
providing adequate ventilation) or directly from outside.
•The stove can be installed in bedrooms or bathrooms using coaxial pipes or by
using external air for combustion.
•Unpack the stove: be careful not to damage the product at the time of unpacking.
•Check the supporting feet of the stove and adjust them so that the item is stable.
•Position the stove so that the door and any window openings are not against the walls.
•After connecting the stove to the combustion air inlet join the coupling device to the flue pipe.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Eva Calor SB 80 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Eva Calor SB 80 in the language / languages: English as an attachment in your email.
The manual is 2.55 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
