Failure to comply with the installation requirements and/or tampering with the stove may result in: inadequate power and/or abnormal product behaviour, poor flue
gas draught, clogging of the fire pit, slow combustion, tank fire, overheating and fire hazard of the stove, fire hazard of the flue gas duct, lack of oxygen in the
environment where the stove is located.
Eva Stampaggi S.r.l. assumes no criminal and/or civil liability, direct and/or indirect for the malfunction of the stove and for damage to persons or property caused
by non-compliance with the requirements for installation of the stove and/or tampering with it.
The Buyer must request and retain the certification of compliance of the installation, and the connection of the stove, with the provisions of law. In the absence of
such certification Eva Stampaggi S.r.l. assumes no criminal and/or civil liability, direct and/or indirect for the malfunction of the stove and for damage caused to
persons or property, resulting from the use of the product.
Warning: in the event of a power failure or electrical blackout, the burn pot must be emptied before repeating the operation.Failure to follow this
procedure may cause the door glass to break.
04. VENT PIPE
THE PRODUCTION OF STOVES WITH HIGHER PERFORMANCE IS INCREASINGLY REQUIRED SO IT IS BECOMES ESSENTIAL TO ENSURE THAT
INSTALLATIONS COMPLY WITH THE LAW. IF THE VENT PIPE PASSESTHROUGH NON-HEATED ENVIRONMENTS, IT MUST BE INSULATED FOR
CORRECT COMBUSTION.
The vent pipe is one of the key features for guaranteeing the proper functioning of the stove. Thanks to the quality of the
materials, the strength, the durability, the easy cleaning and maintenance, the best vent pipes are made of steel, either
stainless steel or aluminised.
•The stove is fitted with a Φ 80mm rear round fume outlet and a joint connection to be connected to the vent pipe.
•To make fitting of the rigid steel flue pipe easier, we recommend using telescopic connectors, which will also
compensate for the thermal dilation both of the fire box and the flue pipe itself.
•Seal the vent pipe joint connection with high temperature silicone sealant (1,000°C). Should the existing flue opening
not be perfectly perpendicular to the firebox fume outlet, use an elbow to connect them. The inclination, with respect to
the vertical, must never exceed 45° (see figure to the side) and there must be no bottlenecks.
•No constrictions. Use 10cm-thick insulating thimbles if pipe vent passes through floors.
•The vent pipe must be insulated along its entire length. Thanks to the vent pipe, insulation fume temperature will remain
high optimising draught, preventing condensation and reducing the build-up of non-ignited particles along the vent pipe
walls. Use proper insulating materials (glass wool, ceramic fibre, Class A1 non-combustible materials).
•The flue must be weatherproof and must not makemore than two changes of direction.
•Flexible and length-adjustable metal pipes may not be used.
EXISTING VENT PIPE EXTERNAL VENT PIPE
Types of vent pipe
Steel vent pipe with double chamber
insulated with
material resistant to 400°C. Optimum efficiency.
Refractory vent pipe with insulated double chamber
and external coating in lightweight concrete. Optimal
efficiency.
Avoid vent pipes with internal rectangular section whose
ratio between the larger and smaller side is greater than 1.5.
Poor efficiency
Traditional clay vent pipe with cavities. Optimal efficiency.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Eva Calor Irma at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Eva Calor Irma in the language / languages: English as an attachment in your email.
The manual is 2.19 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
