668828
50
Zoom out
Zoom in
Previous page
1/55
Next page
PROBLEM CAUSE
SOLUTION
FIRST
START-UP
IT MAY BE NECESSARY TO REPEAT THE FIRST LOAD PHASE A FEW TIMES TO FACILITATE THE
APPLIANCE FIRST START-UP SINCE THE AUGER TUBE IS COMPLETELY EMPTY AND IT MAY TAKE A
SPECIFIC PERIOD OF TIME TO FILL.
DISPLAY
NOT
WORKING
POWER OUTAGE CHECK PLUG AND POWER SUPPLY
FAULTY ELECTRICAL CABLE CALL TECHNICAL ASSISTANCE.
INTERRUPTED FUSE IN
CONTROL BOARD
CALL TECHNICAL ASSISTANCE.
FAULTY CONTROL BOARD CALL TECHNICAL ASSISTANCE.
FAULTY DISPLAY CALL TECHNICAL ASSISTANCE.
ALARM NO FIRE
PELLET
S NOT
FED TO
BURN
POT
PELLET
S FALL
BUT
NOT
LIT
STOVE
SWITCH
ES OFF
DURING
NORMA
L
FUNCTI
ONING
NO PELLETS ALARM NO FIRE
SAFETY THERMOSTAT
TRIGGERED
MANUALLY RESET THE THERMOSTAT LOCATED ON STOVE BACK.
AUGER TUBE BLOCKED BY
FOREIGN BODY
DISCONNECT PLUG, EMPTY HOPPER, REMOVE ANY FOREIGN BODY,
SUCH AS NAILS, ETC.
FAULTY AUGER TUBE MOTOR CALL TECHNICAL ASSISTANCE.
ACTIVE ALARM SEE ALARM SECTION.
DIRTY BURN POT CLEAN BURN POT.
TEMPERATURE TOO COLD
REPEAT SWITCHING-ON PHASE SEVERAL TIMES, EMPTYING THE BURN
POT UPON EACH TIME.
DAMP PELLETS CHECK PELLET STORAGE LOCATION.
FAULTY IGNITION PLUG CALL TECHNICAL ASSISTANCE.
FAULTY FUME SENSOR CALL TECHNICAL ASSISTANCE.
FAULTY EXHAUST BLOWER CALL TECHNICAL ASSISTANCE.
FAULTY CONTROL BOARD CALL TECHNICAL ASSISTANCE.
POWER OUTAGE CHECK PLUG AND POWER SUPPLY.
NO PELLETS CHECK HOPPER
AUGER TUBE BLOCKED BY
FOREIGN BODY
DISCONNECT PLUG, EMPTY HOPPER, REMOVE ANY FOREIGN BODY,
SUCH AS NAILS, ETC.
POOR QUALITY PELLETS CHANGE PELLET TYPE.
INSUFFICIENT PELLET SET
VALUE AT MINIMUM HEAT
OUTPUT
CALL TECHNICAL ASSISTANCE.
ACTIVE ALARM SEE ALARM SECTION.
POOR
FLAME
ANTI-EXPLOSION DEVICE PLUG MISSING OR NOT CORRECTLY POSITIONED.
PARTIALLY CLOGGED VENT
PIPE
CLEAN VENT PIPE IMMEDIATELY.
COMBUSTION AIR NOT
SUFFICIENT
CLOGGED AIR INTAKE.
CLOGGED STOVE CLEAN BURN POT AND ASH DRAWER.
FAULTY / DIRTY EXHAUST
BLOWER
GET IT CLEANED BY A SPECIALISED TECHNICIAN CALL TECHNICAL
ASSISTANCE
INADEQUATE COMBUSTION
AIR SET VALUE
CALL TECHNICAL ASSISTANCE.
ALARM NO
RETE
POWER OUTAGE SWITCH STOVE ON AND OFF, CHECK PLUG.
RiS / ECO
SET ROOM TEMPERATURE REACHED / STOVE WORKS PROPERLY
DISPLAY
DOES NOT
WORK
SET ROOM TEMPERATURE
REACHED
INCREASE SET ROOM TEMPERATURE SO THAT APPLIANCE GOES BACK
TO "WORKING" MODE.
STOP FIRE
PERIODIC CYCLE OF BURN
POT CLEANING
STOVE WORKS PROPERLY
ALARM DEP
EXCESSIVE OR INADEQUATE
VENT PIPE LENGTH
NON-COMPLIANT VENT PIPE
CLOGGED OUTLET CLEAN VENT PIPE / CALL AUTHORISED TECHNICIAN.
BAD WEATHER CONDITIONS STRONG WIND.
50


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eva Calor Hydro 27 kW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eva Calor Hydro 27 kW in the language / languages: English as an attachment in your email.

The manual is 5,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eva Calor Hydro 27 kW

Eva Calor Hydro 27 kW User Manual - German - 38 pages

Eva Calor Hydro 27 kW User Manual - Dutch - 90 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info