668817
40
Zoom out
Zoom in
Previous page
1/55
Next page
- Wait and make sure that the combustion of pellets left in the brazier has been completed.
- RESET THE SAFETY THERMOSTAT located on the rear of the stove under the outlet (see Fig.
14).
Before resetting the safeties, make sure that the stove is off and completely cooled down,
then proceed as follows:
1 Unscrew the cap located on the rear lower right of the stove (see Figure 14).
2 Press the red button with slight pressure.
3 Replace the cap in its housing.
4 After having cleaned the brazier, re-start the stove by pressing button (4).
8.1.3 Smoke temperature sensor
The smoke sensor is directly connected to the circuit board and keeps operating temperature of
exhaust fumes from the stove under constant control, allowing safe use of the stove.
How it works
If fume temperature exceeds the first pre-set temperature limit, the board passes into modulation
mode. The display will show the message MODULATE / MAX SMOKE”. At the same time if,
despite passage to modulation, the fume temperature continues to increase and exceeds the
second pre-set safety limit, the stove will pass into alarm mode. Pellet flow is interrupted and fume
exhaust speed is set to maximum.
The display will show the message “AL 3 – SMOKE TEMP”.
What to do
- Put the stove in stand-by by pressing the off button for a few seconds (4).
-
Wait and make sure that the combustion of pellets left in the brazier has been completed.
-
Verify and remove the causes which caused the safety devices to go off.
-
After having cleaned the brazier, re-start the stove by pressing button (4).
Smoke sensor fault
The stove constantly controls smoke sensor functioning.
When it activates
If the sensor is momentarily and/or accidentally removed from its housing, or the connector is not
correctly positioned on the circuit board or the sensor fails for any reason. The fault is signalled via
display message AL 2 – “SMOKE SENSOR”.
What to do
1 Put the stove in stand-by by pressing the off button for a few seconds (4).
2 Wait and make sure that the combustion of pellets left in the brazier has been completed.
3 If necessary, call a service centre to replace the sensor.
8.1.4 Water temperature sensor
The water sensor is directly connected to the circuit board and keeps operating water temperature
in the boiler under constant control, allowing safe use of the stove.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eva Calor Frida at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eva Calor Frida in the language / languages: English as an attachment in your email.

The manual is 5,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eva Calor Frida

Eva Calor Frida User Manual - German - 38 pages

Eva Calor Frida User Manual - Dutch - 43 pages

Eva Calor Frida User Manual - Dutch - 90 pages

Eva Calor Frida User Manual - French - 43 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info