565032
2
Zoom out
Zoom in
Previous page
1/2
Next page
Transfer to PROGmatic
Following the completion of the programming of your room
pro les you save them onto the stick with the „Save“ button or
via the „Save“ selection in the „File“ menu. Following this you
can remove the stick from the USB port.
Transfer to the energy saving controller
Connect the plug for the EUROtronic Programming Port (see fi gure)
to the corresponding port at the energy saving regulator:
CAUTION ! Progmatic must be disconnected from the computer
during the transfer of the heating pro les!
„P01“ appears on the display. This symbolises „Room pro le 1“.
Depending on the appliance by turning the hand wheel or pressing
the buttons
and the room pro le to be programmed can be
selected for the controller. Only that number of room pro les will
be available for selection as are programmed in the software. The
room pro le is transferred from the stick by subsequently pressing
the
PROG
or
OK
button. After it has been successfully program-
med the standard display can once again be seen on the controller.
Please note that the display automatically returns to its basic state
if you do not perform any changes on the controller within approx.
10 seconds.
Notice upon the initial commissioning of the energy saving
controller:
If you should perform the transfer to a brand new factory energy
saving controller please ensure that the energy saving controller
performs a commissioning procedure.
Skip the entry of the date and time by pressing the
PROG
button
or the
OK
button several times. The correct time is transferred
automatically to the energy saving controller by PROGmatic
following the adaption.
The motor now travels to the
position to facilititate assem-
bly. The notice now appears in the display. Now proceed to the
assembly on the radiator as described in the operating instructors
of the controller.
PROGmatic can now be connected to the energy saving controller.
Cleaning and used appliances
Cleaning
Only use a dry to slightly damp cloth to clean the PROGmatic.
Avoid the use of chemical solvents, you may possibly damage the
appliance by using them.
Used appliances
Do not throw used appliances and packaging into the household
waste. They can be recycled. You can also obtain additional infor-
mation concerning this from your local municipal administration.
Please note:
All the EUROtronic energy saving controllers with a programming
port can be programmed using PROGmatic. If you possess an ener-
gy saving controller with an older manufacturing date the following
functions can differ as described below: No negative value is
accepted for „Offset“. If a negative value is entered in the software
this will be ignored in the energy saving controller.
Technical data
Operating voltage: 5V DC , max. 100mA via USB port
Interfaces: to the PC to the energy saving controller
USB 2.0/EUROtronic programming port
System requirements: from Windows XP® SP3
Number of programmable heating periods: 4 heating periods per
day Function of the LEDs
LED fl ashes red: The Progmatic data has to be updated
LED fl ashes green: Stick is correctly connected to the computer
Protection type: IP30 according to EN 60529
Ambient temperature: 0 to +50
Storage temperature: -20 °C to +70 °C
Casing Material: Plastic ASA
Casing colour: similar to RAL 9016, white
Casing dimensions: approx. 75 x 14 x 34 mm (W x H x D)
Guarantee information
The guarantee period amounts to 24 months and commences on the
day of purchase. Please return the receipt as proof of purchase. Du-
ring the guarantee period defective PROGmatics can be sent with
suf cient postage to the service address stated below. You will
then be sent a new or repaired device in return. A new guarantee
period does not commence upon the repair or replacement of the
device. Following the expiry of the guarantee period you also have
the option of sending the defective device with suf cient postage
to the address stated below for its repair. Repairs that are required
following the expiry of the guarantee period are subject to a charge.
Your statutory rights shall not be restricted by this guarantee.
Eurotronic Technology GmbH
Südweg 1
36396 Steinau-Ulmbach
Tel: +49 (0) 66 67 / 9 18 47-0
Service hotline: +40 (0) 66 67 / 9 18 47-17
eMail: info@eurotronic.org
Internet: www.eurotronic.org
Package no. 900 000 204 1 | As at: 2014/11
www.eurotronic.org
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eurotronic PROGmatic 2014 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eurotronic PROGmatic 2014 in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eurotronic PROGmatic 2014

Eurotronic PROGmatic 2014 User Manual - German - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info