775260

Eurosteel CW Manual

64
Zoom out
Zoom in
Previous page
1/172
Next page
USER MANUAL
CW QUICK COUPLERS FOR EXCAVATORS
TRANSLATION FROM DUTCH ORIGINAL
Eurosteel BV Van Heemskerckweg 10 5928 LL Venlo The Netherlands +31 (0)77 387 60 60 www.eurosteel.nl
- 62 -
- 62 -
USER MANUAL
CW QUICK COUPLERS FOR EXCAVATORS
TRANSLATION FROM DUTCH ORIGINAL
5 OPERATION:
Attachments may only be hooked onto the front shaft by operating the excavator. The attachment is then
attached to the rear shaft by extending the bucket cylinder, and locked hydraulically or mechanically by the
locking wedge.
In the case of a hydraulic version, the CW quick coupler may only be unlocked or locked from the excavator’s
operating position. Mechanical or spindle CW quick couplers must only be locked and unlocked at the CW quick
coupler itself.
THE MAXIMUM PERMITTED LOADS ON THE CW QUICK COUPLER, THE OPTIONAL LIFTING HOOK, THE
OPTIONAL GRAPPLE SUSPENSION AND ATTACHMENTS COUPLED MUST NEVER BE EXCEEDED IN ANY
CIRCUMSTANCES!
WHEN UNLOCKING AND LOCKING, THE ATTACHMENT MUST BE POSITIONED IN A WAY THAT IT
CANNOT DETACH FROM THE CW QUICK COUPLER. IT IS ALSO PROHIBITEDTO BE ON OR BELOW THE
CW QUICK COUPLER OR ATTACHMENT DURING COUPLING, UNCOUPLING, LOCKING OR UNLOCKING
OF THE ATTACHMENT.
IT MAY BE THE CASE THAT YOUR EXCAVATOR IS USED AS A LIFTING MACHINE, HOIST, FOUNDATION
MACHINE ETC. INSTEAD OF AS AN EXCAVATOR, THROUGH THE USE OF THE OPTIONAL LIFTING HOOK
OR COUPLING THE APPROPRIATE ATTACHMENTS. THIS MAY REQUIRE ADDITIONAL SAFETY
MEASURES ON YOUR MACHINE. CONSULT YOUR MACHINE SUPPLIER FOR MORE INFORMATION.
5.1 COUPLING THE ATTACHMENT
Attachments may only be coupled from the operating position of the excavator, where the procedure described
below is followed. If in doubt, contact the supplier of the CW quick coupler.
1. The safety requirements specified in Section 2 must be met before coupling an attachment.
2. The periodic maintenance described in Section 6 must be carried out before using the CW quick
coupler.
3. Before coupling the attachment, determine whether the combination of attachment, CW quick
coupler and excavator is safe. The maximum permitted loads as indicated in Section 1.4 must not be
exceeded, and only attachments in the same CW class may be coupled.
THE CW CLASSES; 2, 3, 4, 4HD OR 2-S, 3-S, 4-S, HAVE EQUAL DIMENSIONS AT THE COUPLING POINTS,
AS SHOWN IN SECTION 1.2 .EQUAL DIMENSIONS AT THE COUPLING POINTS DOES NOT MEAN THAT
THESE ARE EQUAL IN STRUCTURAL TERMS. THE MAXIMUM PERMITTED LOADS ON THE CW QUICK
COUPLER OR THE COUPLED ATTACHMENT MUST NEVER BE EXCEEDED IN ANY CIRCUMSTANCES!
4. Ensure that the coupling surfaces of both the CW quick coupler (see Section 1.3; front shaft, rear shaft,
locking wedge) and the coupling surfaces of the attachment are free from sand and other contaminants,
and that the coupling points are in good condition. See also Section 6, maintenance.
5. Make sure the excavator is level and stable.
6. To couple a attachment to a hydraulic CW quick coupler, follow the steps in Section 5.1.1. To couple a
attachment to a mechanical or spindle version, follow the steps in Section 5.1.2. To couple an
attachment to the optional grapple suspension, see Section 5.1.3.
… 64 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eurosteel CW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eurosteel CW in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 14.32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info