Manual Eurom Wall heater WH2000R (page 12 of 32) (English, German, Dutch, French, Swedish)

591466

Zoom out

Zoom in

1/32

The heater has to preferably be positioned at and permanently connected to an electric socket. This connection

may only be made by a qualified electrician and, for that reason, is not described here.

In this booklet, for reasons of safety, use with a plug should be assumed; when there is a permanent

connection, any passages about the plug do not apply.

 Drill 2 holes in the wall at the chosen location with an 8 mm drill bit: make sure these holes are horizontal and 38.5

mm apart. Insert plugs and screws into the holes. Allow the screws to stick out by 10 mm. Hook the heater over the

screws using the hanging eyes, then pull downwards and slide to the left.

 Check whether the heater is secured to the wall; if necessary insert the screws a little further into the plugs.

 Attach the heater using the materials supplied (see

diagram). Place the bracket on top of the heater, in the

centre (see diagram 2) with the short side against the wall.

Mark the location of the hole on the wall and remove the

heater. Drill a hole at the

marked spot and insert a

plug. Now hang the heater in

place and screw the bracket

to the wall, as shown in the

diagram. The heater is now

installed.

Using for the first time and Operation

 Unroll the electrical cable entirely and insert the plug into a suitable 220/240V socket: 

(HOLD) will light up.

 Press the main switch on

 Press the ON/OFF button: the fan will begin to rotate and the fan indicator lamp (FAN) will light up.

 By pressing the MODE button one or more times, you can set the heater to half of full power or select just fan. The

indicator lamp for the chosen mode will light up as follows:

I = 1000 Watt heating (half power)

II = 2000 Watt heating (full power)

FAN = just ventilation

Press the ON/OFF button again in order to switch the heater off. When you have been using the device to provide heat, it

will cool off for 30 seconds before switching off entirely. During cooling, the FAN indicator lamp will flash on and off. Once



remove the plug from the socket. 

released.

Timer:

The heater is equipped with a timer which can be used to set a specific operational period. Press the timer button

(TIMER) once you have selected a particular mode: by pressing once, you are setting a working time of half an hour;

each time you press again, half an hour will be added, up to a maximum of 7.5 hours. The corresponding indicator lamps

will light up:

0.5h = 0.5 hours

1h = 1 hour

0.5h + 1h = 1.5 hour

And so on up to a maximum of 7.5 hours.

Once the set period has passed, the heater will switch off automatically.

The mode can be changed during operation. If you wish to turn off the device before the set time has been reached,

simply press the ON/OFF button. The heater will now switch off, after any 30 second cooling off period.

Remote control

The heater comes with a remote control with 4 buttons:

ON/OFF This is used to switch the heater on or off. The fan begins to

rotate and the fan lamp lights up.

TIMER Timer button: use this to set an operational period (see above)

1000W Half power. If you press this button while the heater is in operation, it

will heat at half power (1000W).

2000W Full power. If you press this button while the heater is in operation, it

will heat at full power (2000W).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Eurom Wall heater WH2000R in the language / languages: English, German, Dutch, French, Swedish as an attachment in your email.

The manual is 0,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Eurom Wall heater WH2000R Manual

Product: